Following these instructions for hostapd, I was able to get a TX2 access point working.
[url]https://seravo.fi/2014/create-wireless-access-point-hostapd[/url]
However, with original wifi antenna, the signal strength is pretty low, the signal can only cover 3-5 meters.
Has anyone got the same issue?
1 Like
Did you try indoors or outdoors with direct line of sight?
You may want to try using a signal booster or high-gain antenna to gain longer range in your environment.
Thanks for your replying
I tried indoors with the direct line of sight; there’s no block between TX2 and target devices.I just want to make sure I configure TX2 correct.
What’s the average coverage of TX2 with the original antenna?
Hello,
I have been trying to setup WiFi access point on my TX2. I have tried everything in this post:
Do you want to make a computer function as a WLAN base station, so that other computers can use as it as their wifi access point? This can easily be done using the open source software Hostapd and compatible wifi hardware. This is a useful thing to...
Est. reading time: 4 minutes
I have also tried everything suggested in other threads but it is still not working!
I have tried with the latest version of JetPack and an older one.
What usually happens is that, when I try to connect to my AP, I get incorrect password despite me typing the right one.
Any help would be appreciated… Thanks!
Here are the error messages.
[ +0.041849] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[ +0.000259] gpio tegra-gpio-aon wake69 for gpio=59(FF:3)
[ +0.005866] gpio tegra-gpio-aon wake69 for gpio=59(FF:3)
[ +0.005317] Enabling wake69
[ +0.006277] wifi_platform_get_mac_addr
[ +0.001174] Firmware up: op_mode=0x0002, MAC=00:04:4b:8c:fa:f1
[ +0.005877] dhd_preinit_ioctls pspretend_threshold for HostAPD failed -23
[ +0.003378] Firmware version = wl0: Feb 4 2017 14:39:11 version 7.35.221.11 (r623264) FWID 01-5b44953
[ +0.002647] dhd_interworking_enable: failed to set WNM info, ret=-23
[ +0.000203] tegra_sysfs_on
[ +0.068720] CFG80211-ERROR) __wl_cfg80211_scan : Invalid Scan Command at SoftAP mode
[ +0.011287] CFG80211-ERROR) wl_cfg80211_scan : scan error (-22)
[ +0.126268] CFG80211-ERROR) wl_cfg80211_del_station : Disconnect STA : ff:ff:ff:ff:ff:ff scb_val.val 3
[ +0.030764] CFG80211-ERROR) wl_cfg80211_set_channel : netdev_ifidx(4), chan_type(1) target channel(1)
Hi,
So I have been trying to set up a hotspot on my TX2, and I am having problems setting it up. So I followed every step in;
Do you want to make a computer function as a WLAN base station, so that other computers can use as it as their wifi access point? This can easily be done using the open source software Hostapd and compatible wifi hardware. This is a useful thing to...
Est. reading time: 4 minutes
but for reasons, I lose access to all internet connection; both the ethernet and the wifi no longer work, and none of my wifi shows up. is there something I missed
kayccc
March 5, 2020, 2:21am
6
Hi,
So I have been trying to set up a hotspot on my TX2, and I am having problems setting it up. So I followed every step in;
https://seravo.fi/2014/create-wireless-access-point-hostapd
but for reasons, I lose access to all internet connection; both the ethernet and the wifi no longer work, and none of my wifi shows up. is there something I missed
Hi mohammedshittu1,
Please open a new topic for your issue. Be sure to update with JetPack version you used. Thanks