TK1 HDMI video output sync polarity is always negative
When I connect the Jetson TK1 HDMI output to a 1080p60 device it outputs negative sync polarity for both vertical and horizontal even though the EDID specifies positive polarity for both (measured with a quantum data 780E loaded with the device's EDID). Also the xrandr utility lists ALL resolutions as having positive polarity for both vertical and horizontal even though it always outputs negative for both and the EDID specifies other polarities. I've added some printk's to the kernel to see what the X driver is reading from the FBIO_TEGRA_GET_MODEDB ioctl and the polarities look good there. [code] ubuntu@tegra-ubuntu:~$ xrandr --verbose Screen 0: minimum 8 x 8, current 1920 x 1080, maximum 16384 x 16384 HDMI-0 connected primary 1920x1080+0+0 (0x18d) normal (normal left inverted right x axis y axis) 0mm x 0mm Identifier: 0x18c Timestamp: 18506 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 0 CRTCs: 0 1 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: EDID: 00ffffffffffff00170e000000000000 001a010380000078ee00000000000000 000000210800810081809500a9c0b300 a94001010101023a801871382d40582c 450080387400001e000000fd00173d0e 963c000a202020202020000000ff000a 202020202020202020202020000000fc 00457874726f6e5363616c65724401f8 020346f05c616066655f645d625e6390 1f222120051404130302121107061615 0123090707830100006e030c001000b8 3c2000800102030467d85dc401788003 e200eae20f0f00000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 000000000000000000000000000000e6 BorderDimensions: 4 supported: 4 Border: 0 0 0 0 range: (0, 65535) SignalFormat: TMDS supported: TMDS ConnectorType: HDMI 1920x1080 (0x18d) 148.5MHz +HSync +VSync *current +preferred h: width 1920 start 2008 end 2052 total 2200 skew 0 clock 67.5KHz v: height 1080 start 1084 end 1089 total 1125 clock 60.0Hz 4096x2160 (0x18e) 297.0MHz +HSync +VSync h: width 4096 start 5116 end 5204 total 5500 skew 0 clock 54.0KHz v: height 2160 start 2168 end 2178 total 2250 clock 24.0Hz 3840x2160 (0x18f) 297.0MHz +HSync +VSync h: width 3840 start 4016 end 4104 total 4400 skew 0 clock 67.5KHz v: height 2160 start 2168 end 2178 total 2250 clock 30.0Hz 3840x2160 (0x190) 297.0MHz +HSync +VSync h: width 3840 start 4896 end 4984 total 5280 skew 0 clock 56.2KHz v: height 2160 start 2168 end 2178 total 2250 clock 25.0Hz 3840x2160 (0x191) 297.0MHz +HSync +VSync h: width 3840 start 5116 end 5204 total 5500 skew 0 clock 54.0KHz v: height 2160 start 2168 end 2178 total 2250 clock 24.0Hz 1920x1080 (0x192) 148.5MHz +HSync +VSync h: width 1920 start 2448 end 2492 total 2640 skew 0 clock 56.2KHz v: height 1080 start 1084 end 1089 total 1125 clock 50.0Hz 1920x1080 (0x193) 74.2MHz +HSync +VSync h: width 1920 start 2008 end 2052 total 2200 skew 0 clock 33.8KHz v: height 1080 start 1082 end 1087 total 1102 clock 30.6Hz 1920x1080 (0x194) 74.2MHz +HSync +VSync h: width 1920 start 2008 end 2052 total 2200 skew 0 clock 33.8KHz v: height 1080 start 1084 end 1089 total 1125 clock 30.0Hz 1920x1080 (0x195) 74.2MHz +HSync +VSync h: width 1920 start 2448 end 2492 total 2640 skew 0 clock 28.1KHz v: height 1080 start 1082 end 1087 total 1102 clock 25.5Hz 1920x1080 (0x196) 74.2MHz +HSync +VSync h: width 1920 start 2448 end 2492 total 2640 skew 0 clock 28.1KHz v: height 1080 start 1084 end 1089 total 1125 clock 25.0Hz 1920x1080 (0x197) 74.2MHz +HSync +VSync h: width 1920 start 2558 end 2602 total 2750 skew 0 clock 27.0KHz v: height 1080 start 1084 end 1089 total 1125 clock 24.0Hz 1680x1050 (0x198) 146.9MHz +HSync +VSync h: width 1680 start 1786 end 1966 total 2252 skew 0 clock 65.2KHz v: height 1050 start 1052 end 1055 total 1087 clock 60.0Hz 1600x1200 (0x199) 162.0MHz +HSync +VSync h: width 1600 start 1664 end 1856 total 2160 skew 0 clock 75.0KHz v: height 1200 start 1202 end 1205 total 1250 clock 60.0Hz 1600x900 (0x19a) 118.6MHz +HSync +VSync h: width 1600 start 1692 end 1861 total 2122 skew 0 clock 55.9KHz v: height 900 start 902 end 905 total 932 clock 60.0Hz 1440x900 (0x19b) 106.8MHz +HSync +VSync h: width 1440 start 1523 end 1675 total 1910 skew 0 clock 55.9KHz v: height 900 start 902 end 905 total 932 clock 60.0Hz 1280x1024 (0x19c) 108.0MHz +HSync +VSync h: width 1280 start 1328 end 1440 total 1688 skew 0 clock 64.0KHz v: height 1024 start 1026 end 1029 total 1066 clock 60.0Hz 1280x800 (0x19d) 83.6MHz +HSync +VSync h: width 1280 start 1347 end 1481 total 1683 skew 0 clock 49.7KHz v: height 800 start 802 end 805 total 828 clock 60.0Hz 1280x720 (0x19e) 74.2MHz +HSync +VSync h: width 1280 start 1390 end 1430 total 1650 skew 0 clock 45.0KHz v: height 720 start 725 end 730 total 750 clock 60.0Hz 1280x720 (0x19f) 74.2MHz +HSync +VSync h: width 1280 start 1720 end 1760 total 1980 skew 0 clock 37.5KHz v: height 720 start 725 end 730 total 750 clock 50.0Hz 1024x768 (0x1a0) 65.0MHz +HSync +VSync h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz v: height 768 start 771 end 777 total 806 clock 60.0Hz 640x480 (0x1a1) 25.2MHz +HSync +VSync h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz v: height 480 start 482 end 484 total 516 clock 61.0Hz 640x480 (0x1a2) 25.2MHz +HSync +VSync h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz v: height 480 start 490 end 492 total 525 clock 60.0Hz [/code]
When I connect the Jetson TK1 HDMI output to a 1080p60 device it outputs negative sync polarity for both vertical and horizontal even though the EDID specifies positive polarity for both (measured with a quantum data 780E loaded with the device's EDID).

Also the xrandr utility lists ALL resolutions as having positive polarity for both vertical and horizontal even though it always outputs negative for both and the EDID specifies other polarities.

I've added some printk's to the kernel to see what the X driver is reading from the FBIO_TEGRA_GET_MODEDB ioctl and the polarities look good there.

ubuntu@tegra-ubuntu:~$ xrandr --verbose
Screen 0: minimum 8 x 8, current 1920 x 1080, maximum 16384 x 16384
HDMI-0 connected primary 1920x1080+0+0 (0x18d) normal (normal left inverted right x axis y axis) 0mm x 0mm
Identifier: 0x18c
Timestamp: 18506
Subpixel: unknown
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 0
CRTCs: 0 1
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID:
00ffffffffffff00170e000000000000
001a010380000078ee00000000000000
000000210800810081809500a9c0b300
a94001010101023a801871382d40582c
450080387400001e000000fd00173d0e
963c000a202020202020000000ff000a
202020202020202020202020000000fc
00457874726f6e5363616c65724401f8
020346f05c616066655f645d625e6390
1f222120051404130302121107061615
0123090707830100006e030c001000b8
3c2000800102030467d85dc401788003
e200eae20f0f00000000000000000000
00000000000000000000000000000000
00000000000000000000000000000000
000000000000000000000000000000e6
BorderDimensions: 4
supported: 4
Border: 0 0 0 0
range: (0, 65535)
SignalFormat: TMDS
supported: TMDS
ConnectorType: HDMI
1920x1080 (0x18d) 148.5MHz +HSync +VSync *current +preferred
h: width 1920 start 2008 end 2052 total 2200 skew 0 clock 67.5KHz
v: height 1080 start 1084 end 1089 total 1125 clock 60.0Hz
4096x2160 (0x18e) 297.0MHz +HSync +VSync
h: width 4096 start 5116 end 5204 total 5500 skew 0 clock 54.0KHz
v: height 2160 start 2168 end 2178 total 2250 clock 24.0Hz
3840x2160 (0x18f) 297.0MHz +HSync +VSync
h: width 3840 start 4016 end 4104 total 4400 skew 0 clock 67.5KHz
v: height 2160 start 2168 end 2178 total 2250 clock 30.0Hz
3840x2160 (0x190) 297.0MHz +HSync +VSync
h: width 3840 start 4896 end 4984 total 5280 skew 0 clock 56.2KHz
v: height 2160 start 2168 end 2178 total 2250 clock 25.0Hz
3840x2160 (0x191) 297.0MHz +HSync +VSync
h: width 3840 start 5116 end 5204 total 5500 skew 0 clock 54.0KHz
v: height 2160 start 2168 end 2178 total 2250 clock 24.0Hz
1920x1080 (0x192) 148.5MHz +HSync +VSync
h: width 1920 start 2448 end 2492 total 2640 skew 0 clock 56.2KHz
v: height 1080 start 1084 end 1089 total 1125 clock 50.0Hz
1920x1080 (0x193) 74.2MHz +HSync +VSync
h: width 1920 start 2008 end 2052 total 2200 skew 0 clock 33.8KHz
v: height 1080 start 1082 end 1087 total 1102 clock 30.6Hz
1920x1080 (0x194) 74.2MHz +HSync +VSync
h: width 1920 start 2008 end 2052 total 2200 skew 0 clock 33.8KHz
v: height 1080 start 1084 end 1089 total 1125 clock 30.0Hz
1920x1080 (0x195) 74.2MHz +HSync +VSync
h: width 1920 start 2448 end 2492 total 2640 skew 0 clock 28.1KHz
v: height 1080 start 1082 end 1087 total 1102 clock 25.5Hz
1920x1080 (0x196) 74.2MHz +HSync +VSync
h: width 1920 start 2448 end 2492 total 2640 skew 0 clock 28.1KHz
v: height 1080 start 1084 end 1089 total 1125 clock 25.0Hz
1920x1080 (0x197) 74.2MHz +HSync +VSync
h: width 1920 start 2558 end 2602 total 2750 skew 0 clock 27.0KHz
v: height 1080 start 1084 end 1089 total 1125 clock 24.0Hz
1680x1050 (0x198) 146.9MHz +HSync +VSync
h: width 1680 start 1786 end 1966 total 2252 skew 0 clock 65.2KHz
v: height 1050 start 1052 end 1055 total 1087 clock 60.0Hz
1600x1200 (0x199) 162.0MHz +HSync +VSync
h: width 1600 start 1664 end 1856 total 2160 skew 0 clock 75.0KHz
v: height 1200 start 1202 end 1205 total 1250 clock 60.0Hz
1600x900 (0x19a) 118.6MHz +HSync +VSync
h: width 1600 start 1692 end 1861 total 2122 skew 0 clock 55.9KHz
v: height 900 start 902 end 905 total 932 clock 60.0Hz
1440x900 (0x19b) 106.8MHz +HSync +VSync
h: width 1440 start 1523 end 1675 total 1910 skew 0 clock 55.9KHz
v: height 900 start 902 end 905 total 932 clock 60.0Hz
1280x1024 (0x19c) 108.0MHz +HSync +VSync
h: width 1280 start 1328 end 1440 total 1688 skew 0 clock 64.0KHz
v: height 1024 start 1026 end 1029 total 1066 clock 60.0Hz
1280x800 (0x19d) 83.6MHz +HSync +VSync
h: width 1280 start 1347 end 1481 total 1683 skew 0 clock 49.7KHz
v: height 800 start 802 end 805 total 828 clock 60.0Hz
1280x720 (0x19e) 74.2MHz +HSync +VSync
h: width 1280 start 1390 end 1430 total 1650 skew 0 clock 45.0KHz
v: height 720 start 725 end 730 total 750 clock 60.0Hz
1280x720 (0x19f) 74.2MHz +HSync +VSync
h: width 1280 start 1720 end 1760 total 1980 skew 0 clock 37.5KHz
v: height 720 start 725 end 730 total 750 clock 50.0Hz
1024x768 (0x1a0) 65.0MHz +HSync +VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz
v: height 768 start 771 end 777 total 806 clock 60.0Hz
640x480 (0x1a1) 25.2MHz +HSync +VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 482 end 484 total 516 clock 61.0Hz
640x480 (0x1a2) 25.2MHz +HSync +VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz
v: height 480 start 490 end 492 total 525 clock 60.0Hz

#1
Posted 02/09/2018 05:58 PM   
Please share below information 1. Are you using devkit or custom carrier board? 2. Are other monitors working well on your tk1? 3. Please share full dmesg as an attachment. Your monitor is powered on but blanked, is it?
Please share below information

1. Are you using devkit or custom carrier board?

2. Are other monitors working well on your tk1?

3. Please share full dmesg as an attachment.

Your monitor is powered on but blanked, is it?

#2
Posted 02/12/2018 02:42 AM   
1. The Jetson TK1 does not have a carrier board. 2. Sync polarities are always negative with all EDIDs tried. 3. dmesg: [code] ubuntu@tegra-ubuntu:~$ dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.40-gb271e8f (buildbrain@mobile-u64-57) (gcc version 4.5.3 (crosstool-NG hg_unknown@20110628.165246) ) #1 SMP PREEMPT Fri Oct 13 18:07:53 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine: jetson-tk1, model: NVIDIA Tegra124 PM375, serial: 0 [ 0.000000] Truncating memory at 0x80000000 to fit in 32-bit physical address space [ 0.000000] Found tsec, start=0xf4900000 size=2000000 [ 0.000000] Tegra reserved memory: [ 0.000000] LP0: f46ff000 - f46ff80f [ 0.000000] Bootloader framebuffer: 00000000 - 00000000 [ 0.000000] Bootloader framebuffer2: 00000000 - 00000000 [ 0.000000] Framebuffer: f8500000 - f96fffff [ 0.000000] 2nd Framebuffer: f9700000 - fdefffff [ 0.000000] Carveout: 00000000 - 00000000 [ 0.000000] Vpr: 00000000 - 00000000 [ 0.000000] Tsec: f4900000 - f68fffff [ 0.000000] cma: CMA: reserved 16 MiB at ae800000 [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] On node 0 totalpages: 492288 [ 0.000000] free_area_init_node: node 0, pgdat c0d25c80, node_mem_map c0e09000 [ 0.000000] Normal zone: 1520 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 2510 pages used for memmap [ 0.000000] HighMem zone: 297728 pages, LIFO batch:31 [ 0.000000] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/arch/arm/boot/dts/tegra124-jetson_tk1-pm375-000-c00-00.dts [ 0.000000] Tegra12: CPU Speedo value 2286, Soc Speedo value 2208, Gpu Speedo value 2064 [ 0.000000] Tegra12: CPU Speedo ID 1, Soc Speedo ID 1, Gpu Speedo ID 1 [ 0.000000] Tegra12: CPU Process ID 1,Soc Process ID 1,Gpu Process ID 1 [ 0.000000] Tegra Revision: A01 SKU: 0x81 CPU Process: 1 Core Process: 1 [ 0.000000] tegra: PLLP fixed rate: 408000000 [ 0.000000] tegra_clk_shared_bus_user_init: c2bus client se left ON [ 0.000000] tegra_clk_shared_bus_user_init: c4bus client vi left ON [ 0.000000] Lowering cpu_lp maximum rate from 1350000000 to 1092000000 [ 0.000000] Lowering sbus maximum rate from 420000000 to 384000000 [ 0.000000] Lowering vic03 maximum rate from 900000000 to 828000000 [ 0.000000] Lowering tsec maximum rate from 900000000 to 828000000 [ 0.000000] Lowering msenc maximum rate from 600000000 to 528000000 [ 0.000000] Lowering se maximum rate from 600000000 to 528000000 [ 0.000000] Lowering vde maximum rate from 600000000 to 528000000 [ 0.000000] Lowering host1x maximum rate from 500000000 to 444000000 [ 0.000000] Lowering vi maximum rate from 700000000 to 600000000 [ 0.000000] Lowering isp maximum rate from 700000000 to 600000000 [ 0.000000] Lowering c4bus maximum rate from 700000000 to 600000000 [ 0.000000] Lowering pll_c maximum rate from 1400000000 to 1066000000 [ 0.000000] Lowering pll_c2 maximum rate from 1200000000 to 1066000000 [ 0.000000] Lowering pll_c3 maximum rate from 1200000000 to 1066000000 [ 0.000000] Lowering hdmi maximum rate from 594000000 to 297000000 [ 0.000000] Lowering sdmmc1 maximum rate from 208000000 to 204000000 [ 0.000000] Lowering sdmmc3 maximum rate from 208000000 to 204000000 [ 0.000000] Lowering gbus maximum rate from 1032000000 to 852000000 [ 0.000000] Lowering cpu_g maximum rate from 3000000000 to 2065500000 [ 0.000000] tegra dvfs: VDD_CPU nominal 1260mV, scaling enabled [ 0.000000] tegra dvfs: VDD_CORE nominal 1150mV, scaling enabled [ 0.000000] tegra dvfs: VDD_GPU nominal 1200mV, scaling enabled [ 0.000000] Switching to timer-based delay loop [ 0.000000] tegra_powergate_init: DONE [ 0.000000] tegra12_plle_clk_enable: pll_e is already enabled [ 0.000000] PERCPU: Embedded 9 pages/cpu @c1df3000 s15168 r8192 d13504 u36864 [ 0.000000] pcpu-alloc: s15168 r8192 d13504 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 490768 [ 0.000000] Kernel command line: console=ttyS0,115200n8 console=tty1 no_console_suspend=1 lp0_vec=2064@0xf46ff000 mem=2015M@2048M memtype=255 ddr_die=2048M@2048M section=256M pmuboard=0x0177:0x0000:0x02:0x43:0x00 tsec=32M@3913M otf_key=c75e5bb91eb3bd947560357b64422f85 usbcore.old_scheme_first=1 core_edp_mv=1150 core_edp_ma=4000 tegraid=40.1.1.0.0 debug_uartport=lsport,3 power_supply=Adapter audio_codec=rt5640 modem_id=0 android.kerneltype=normal fbcon=map:1 commchip_id=0 usb_port_owner_info=0 lane_owner_info=6 emc_max_dvfs=0 touch_id=0@0 board_info=0x0177:0x0000:0x02:0x43:0x00 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait tegraboot=sdmmc gpt [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1923MB = 1923MB total [ 0.000000] Memory: 1920996k/1920996k available, 142364k reserved, 1190908K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0b5b6f4 (11598 kB) [ 0.000000] .init : 0xc0b5c000 - 0xc0bd8b40 ( 499 kB) [ 0.000000] .data : 0xc0bda000 - 0xc0d3efd4 (1428 kB) [ 0.000000] .bss : 0xc0d3efd4 - 0xc0dd9f0c ( 620 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:960 [ 0.000000] the number of interrupt controllers found is 5 [ 0.000000] Architected local timer running at 12.00MHz (phys). [ 0.000000] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 2863311536128ns [ 0.000000] Ignoring duplicate/late registration of read_current_timer delay [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty1] enabled [ 0.003809] Calibrating delay loop (skipped), value calculated using timer frequency.. lpj=12000 [ 0.003880] pid_max: default: 32768 minimum: 301 [ 0.004180] Mount-cache hash table entries: 512 [ 0.027664] Initializing cgroup subsys debug [ 0.027710] Initializing cgroup subsys freezer [ 0.027795] CPU: Testing write buffer coherency: ok [ 0.027890] ftrace: allocating 33486 entries in 66 pages [ 0.070299] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.070343] Setting up static identity map for 0xc0824af8 - 0xc0824b94 [ 0.074335] ftrace: Allocated trace_printk buffers [ 0.082028] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.085033] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.088076] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.088270] Brought up 4 CPUs [ 0.088334] SMP: Total of 4 processors activated. [ 0.088352] CPU: All CPU(s) started in SVC mode. [ 0.089218] devtmpfs: initialized [ 0.098110] pinctrl core: initialized pinctrl subsystem [ 0.098436] regulator-dummy: no parameters [ 0.099140] NET: Registered protocol family 16 [ 0.101494] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.102740] tegra_smmu tegra_smmu: Loaded Tegra IOMMU driver [ 0.104168] console [pstore-1] enabled [ 0.104206] ramoops: attached 0x200000@0xf8300000, ecc: 0/0 [ 0.104595] cpuidle: using governor ladder [ 0.104619] cpuidle: using governor menu [ 0.108446] ardbeg_camera_auxdata: update camera lookup table. [ 0.117415] tegra-gpio 6000d000.gpio: Initialising GPIO state 0: name default [ 0.117824] gpiochip_add: registered GPIOs 0 to 255 on device: tegra-gpio [ 0.124703] Wake16 for irq=34 [ 0.127198] Wake58 for irq=81 [ 0.127248] Wake41 for irq=129 [ 0.127268] Wake43 for irq=129 [ 0.127315] Wake40 for irq=53 [ 0.127333] Wake42 for irq=53 [ 0.131570] board_info: id:sku:fab:major:minor = 0x0177:0x0000:0x42:0x44:0x00 [ 0.131656] board_info: id:sku:fab:major:minor = 0x0177:0x0000:0x42:0x44:0x00 [ 0.131722] disp1 pclk=154700000 [ 0.131732] disp2 pclk=297000000 [ 0.131741] Selecting UARTD as the debug console [ 0.131789] The debug console clock name is uartd [ 0.132215] ardbeg_modem_init: modem_id = 0 [ 0.134890] Clear bootloader IO dpd settings [ 0.135131] Loading jetson TK1 EMC tables. [ 0.135381] tegra: pll_m is selected as scalable EMC clock source [ 0.135425] Lowering emc maximum rate from 1200000000 to 924000000 [ 0.135453] tegra: validated EMC DFS table [ 0.135585] ardbeg_edp_init: CPU regulator 12500 mA [ 0.401607] ardbeg_edp_init: GPU regulator 11400 mA [ 0.402602] swapper/0 isomgr_init(): iso emc max clk=924000KHz [ 0.402623] swapper/0 isomgr_init(): max_iso_bw=7392000KB<6>[ 0.403007] ardbeg_touch_init init raydium touch [ 0.403168] Raydium - touch platform_id : 8 [ 0.486093] platform tegradc.0: IOVA linear map 0xf8500000(1200000) [ 0.489408] platform tegradc.0: IOVA linear map 0xf9700000(4800000) [ 0.494429] platform tegradc.1: IOVA linear map 0xf8500000(1200000) [ 0.497741] platform tegradc.1: IOVA linear map 0xf9700000(4800000) [ 0.498178] FUSE: cp_rev 0 ft_rev 0 [ 0.498356] tegra11_soctherem_oc_int_init(): OC interrupts are not enabled [ 0.498784] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.498816] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.499054] mc-err: Started MC error interface! [ 0.509808] bio: create slab <bio-0> at 0 [ 0.511766] reg-fixed-voltage 0.regulator: Consumer c1 does not have device name [ 0.511804] reg-fixed-voltage 0.regulator: Consumer c2 does not have device name [ 0.511836] of_get_named_gpio_flags: can't parse gpios property [ 0.511958] vdd-ac-bat: 8400 mV [ 0.512097] reg-fixed-voltage 1.regulator: Consumer c1 does not have device name [ 0.512130] reg-fixed-voltage 1.regulator: Consumer c2 does not have device name [ 0.512160] of_get_named_gpio_flags: can't parse gpios property [ 0.512265] vdd-3v3-aon: 3300 mV [ 0.512417] reg-fixed-voltage 8.regulator: Consumer c1 does not have device name [ 0.512451] reg-fixed-voltage 8.regulator: Consumer c2 does not have device name [ 0.512483] reg-fixed-voltage 8.regulator: Consumer c3 does not have device name [ 0.512519] reg-fixed-voltage 8.regulator: Consumer c6 does not have device name [ 0.512550] reg-fixed-voltage 8.regulator: Consumer c7 does not have device name [ 0.512581] reg-fixed-voltage 8.regulator: Consumer c8 does not have device name [ 0.512611] reg-fixed-voltage 8.regulator: Consumer c9 does not have device name [ 0.512642] reg-fixed-voltage 8.regulator: Consumer c10 does not have device name [ 0.512673] reg-fixed-voltage 8.regulator: Consumer c11 does not have device name [ 0.512704] reg-fixed-voltage 8.regulator: Consumer c12 does not have device name [ 0.512749] of_get_named_gpio_flags: can't parse gpios property [ 0.512835] reg-3v3-supply: 3300 mV [ 0.514489] vgaarb: loaded [ 0.515125] SCSI subsystem initialized [ 0.515332] libata version 3.00 loaded. [ 0.515522] usbcore: registered new interface driver usbfs [ 0.515588] usbcore: registered new interface driver hub [ 0.515721] usbcore: registered new device driver usb [ 0.515952] of_get_named_gpio_flags exited with status 20 [ 0.515992] of_get_named_gpio_flags exited with status 21 [ 0.516411] of_get_named_gpio_flags exited with status 157 [ 0.516429] of_get_named_gpio_flags exited with status 158 [ 0.516660] of_get_named_gpio_flags exited with status 217 [ 0.516676] of_get_named_gpio_flags exited with status 218 [ 0.516908] of_get_named_gpio_flags exited with status 172 [ 0.516926] of_get_named_gpio_flags exited with status 173 [ 0.517183] of_get_named_gpio_flags exited with status 206 [ 0.517200] of_get_named_gpio_flags exited with status 207 [ 0.518611] as3722 4-0040: AS3722 ID: ID1:ID2:ID3 = 0x0c:0x01:0x15 [ 0.518641] as3722 4-0040: Final OTP version 1V21 [ 0.523320] gpiochip_find_base: found new base at 1016 [ 0.523418] gpiochip_add: registered GPIOs 1016 to 1023 on device: as3722-gpio [ 0.523455] GPIO chip as3722-gpio: created GPIO range 0->7 ==> as3722-pinctrl PIN 0->7 [ 0.523623] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name [ 0.523684] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name [ 0.523737] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name [ 0.523770] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name [ 0.523803] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name [ 0.523835] as3722-regulator as3722-regulator.0: Consumer c4 does not have device name [ 0.523894] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name [ 0.523926] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name [ 0.523958] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name [ 0.523989] as3722-regulator as3722-regulator.0: Consumer c4 does not have device name [ 0.524020] as3722-regulator as3722-regulator.0: Consumer c5 does not have device name [ 0.524052] as3722-regulator as3722-regulator.0: Consumer c6 does not have device name [ 0.524084] as3722-regulator as3722-regulator.0: Consumer c7 does not have device name [ 0.524168] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name [ 0.524201] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name [ 0.524233] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name [ 0.524265] as3722-regulator as3722-regulator.0: Consumer c4 does not have device name [ 0.524299] as3722-regulator as3722-regulator.0: Consumer c6 does not have device name [ 0.524333] as3722-regulator as3722-regulator.0: Consumer c8 does not have device name [ 0.524364] as3722-regulator as3722-regulator.0: Consumer c9 does not have device name [ 0.524396] as3722-regulator as3722-regulator.0: Consumer c10 does not have device name [ 0.524428] as3722-regulator as3722-regulator.0: Consumer c11 does not have device name [ 0.524460] as3722-regulator as3722-regulator.0: Consumer c12 does not have device name [ 0.524492] as3722-regulator as3722-regulator.0: Consumer c13 does not have device name [ 0.524524] as3722-regulator as3722-regulator.0: Consumer c14 does not have device name [ 0.524556] as3722-regulator as3722-regulator.0: Consumer c15 does not have device name [ 0.524612] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name [ 0.524643] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name [ 0.524698] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name [ 0.524730] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name [ 0.524761] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name [ 0.524792] as3722-regulator as3722-regulator.0: Consumer c4 does not have device name [ 0.524824] as3722-regulator as3722-regulator.0: Consumer c5 does not have device name [ 0.524855] as3722-regulator as3722-regulator.0: Consumer c6 does not have device name [ 0.524887] as3722-regulator as3722-regulator.0: Consumer c7 does not have device name [ 0.524918] as3722-regulator as3722-regulator.0: Consumer c8 does not have device name [ 0.524950] as3722-regulator as3722-regulator.0: Consumer c9 does not have device name [ 0.525008] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name [ 0.525040] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name [ 0.525147] as3722-regulator as3722-regulator.0: Consumer c8 does not have device name [ 0.525181] as3722-regulator as3722-regulator.0: Consumer c9 does not have device name [ 0.525212] as3722-regulator as3722-regulator.0: Consumer c10 does not have device name [ 0.525270] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name [ 0.525320] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name [ 0.525352] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name [ 0.525383] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name [ 0.525439] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name [ 0.525471] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name [ 0.525529] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name [ 0.525584] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name [ 0.525616] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name [ 0.525690] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name [ 0.525722] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name [ 0.525754] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name [ 0.526672] vdd-cpu: 650 <--> 1300 mV at 1000 mV 3500 mA [ 0.527444] vdd-core: applied init 1150000uV constraint [ 0.528049] vdd-core: 700 <--> 1350 mV at 1150 mV 3500 mA [ 0.529246] vddio-ddr: at 1350 mV [ 0.529573] as3722-sd3: no parameters [ 0.530154] avdd-pll-pex: 1050 mV [ 0.531385] vdd-1v8: at 1800 mV [ 0.531745] vdd-gpu: applied init 1000000uV constraint [ 0.532625] vdd-gpu: 650 <--> 1200 mV at 1000 mV 3500 mA [ 0.533129] avdd-pll: at 1050 mV at 300 mA [ 0.534417] vdd-cam: 1800 mV at 150 mA [ 0.535088] avdd-dsi-csi: at 1200 mV at 150 mA [ 0.536314] vdd-rtc: 800 mV at 150 mA [ 0.536790] avdd-cam: 2800 mV at 150 mA [ 0.537299] vdd-1v2-cam: 1175 mV at 150 mA [ 0.537672] vddio-sdmmc-2: 1800 <--> 3300 mV at 150 mA [ 0.538172] vdd-1v1-cam: 1275 mV at 150 mA [ 0.539147] avdd-spi: 3300 mV at 150 mA [ 0.539668] vdd-2v7-cam: 2800 mV at 150 mA [ 0.540176] vpp-fuse: 1800 mV at 150 mA [ 0.540794] of_get_named_gpio_flags: can't parse gpios property [ 0.540805] of_get_named_gpio_flags: can't parse gpios property [ 0.541282] Linux video capture interface: v2.00 [ 0.542433] Advanced Linux Sound Architecture Driver Initialized. [ 0.542880] ardbeg_wifi_power: 1 [ 0.643261] of_get_named_gpio_flags exited with status 108 [ 0.643391] usb0-vbus: 5000 mV [ 0.643577] of_get_named_gpio_flags exited with status 109 [ 0.643699] usb1-usb2-vbus: 5000 mV [ 0.643879] of_get_named_gpio_flags exited with status 86 [ 0.643989] vdd-hdmi: 5000 mV [ 0.644182] of_get_named_gpio_flags exited with status 63 [ 0.644294] avdd-hdmi-pll: 3300 mV [ 0.644345] avdd-hdmi-pll: supplied by avdd-pll-pex [ 0.644515] reg-fixed-sync-voltage 6.regulator: Consumer c1 does not have device name [ 0.644559] of_get_named_gpio_flags exited with status 122 [ 0.644660] vdd-lcd-bl: 3300 mV [ 0.644819] reg-fixed-sync-voltage 7.regulator: Consumer c1 does not have device name [ 0.644863] of_get_named_gpio_flags exited with status 58 [ 0.644972] vdd-lcd-bl-en: 5000 mV [ 0.645149] reg-fixed-sync-voltage 9.regulator: Consumer c3 does not have device name [ 0.645180] of_get_named_gpio_flags: can't parse gpios property [ 0.645269] reg-5v0-supply: 5000 mV [ 0.645436] reg-fixed-sync-voltage a.regulator: Consumer c1 does not have device name [ 0.645470] reg-fixed-sync-voltage a.regulator: Consumer c2 does not have device name [ 0.645502] reg-fixed-sync-voltage a.regulator: Consumer c3 does not have device name [ 0.645551] reg-fixed-sync-voltage a.regulator: Consumer c10 does not have device name [ 0.645584] reg-fixed-sync-voltage a.regulator: Consumer c11 does not have device name [ 0.645615] reg-fixed-sync-voltage a.regulator: Consumer c12 does not have device name [ 0.645647] reg-fixed-sync-voltage a.regulator: Consumer c13 does not have device name [ 0.645678] reg-fixed-sync-voltage a.regulator: Consumer c14 does not have device name [ 0.645710] reg-fixed-sync-voltage a.regulator: Consumer c15 does not have device name [ 0.645765] of_get_named_gpio_flags: can't parse gpios property [ 0.645854] reg-1v8-supply: 1800 mV [ 0.646197] reg-fixed-sync-voltage b.regulator: Consumer c1 does not have device name [ 0.646242] of_get_named_gpio_flags exited with status 138 [ 0.646351] reg-dcdc-1v2: 1200 mV [ 0.646531] reg-fixed-sync-voltage c.regulator: Consumer c7 does not have device name [ 0.646565] reg-fixed-sync-voltage c.regulator: Consumer c8 does not have device name [ 0.646609] of_get_named_gpio_flags exited with status 1018 [ 0.647158] as3722-gpio2-supply: 3300 mV [ 0.647363] reg-fixed-sync-voltage d.regulator: Consumer c1 does not have device name [ 0.647409] of_get_named_gpio_flags exited with status 1020 [ 0.647885] as3722-gpio4-supply: 3300 mV [ 0.648060] of_get_named_gpio_flags exited with status 136 [ 0.648197] sdmmc-en-supply: 3300 mV [ 0.648370] of_get_named_gpio_flags exited with status 138 [ 0.648462] vdd-cdc-1v2-aud: 1200 mV [ 0.648619] reg-fixed-sync-voltage 10.regulator: Consumer c1 does not have device name [ 0.648654] reg-fixed-sync-voltage 10.regulator: Consumer c2 does not have device name [ 0.648687] reg-fixed-sync-voltage 10.regulator: Consumer c3 does not have device name [ 0.648717] of_get_named_gpio_flags: can't parse gpios property [ 0.648811] reg-aon-1v8: 1800 mV [ 0.648975] reg-fixed-sync-voltage 11.regulator: Consumer c1 does not have device name [ 0.649007] of_get_named_gpio_flags: can't parse gpios property [ 0.649102] reg-aon-1v2: 1200 mV [ 0.652139] as3722-adc-extcon as3722-adc-extcon.2: USB-Host is disconnected [ 0.655541] tegra: started io power detection dynamic control [ 0.655568] tegra: NO_IO_POWER setting 0x0 [ 0.655595] Switching to clocksource arch_sys_counter [ 0.677047] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.677239] nvmap_page_pool_init: Total MB RAM: 1891 [ 0.677264] nvmap_page_pool_init: nvmap page pool size: 60543 pages (236 MB) [ 0.677422] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.677593] iram: dma coherent mem declare 0x40001000,258048 [ 0.678437] misc nvmap: created heap iram base 0x40001000 size (252KiB) [ 0.678602] nvmap:inner cache maint threshold=2097152 [ 0.688550] Wake39 for irq=52 [ 0.688648] tegra-otg tegra-otg: otg transceiver registered [ 0.689030] NET: Registered protocol family 2 [ 0.689706] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.689914] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.690117] TCP: Hash tables configured (established 8192 bind 8192) [ 0.690179] TCP: reno registered [ 0.690205] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.690262] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.690552] NET: Registered protocol family 1 [ 0.690961] RPC: Registered named UNIX socket transport module. [ 0.690988] RPC: Registered udp transport module. [ 0.691009] RPC: Registered tcp transport module. [ 0.691029] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.691056] PCI: CLS 0 bytes, default 64 [ 0.691318] tegra-fuse tegra-fuse: Fuse driver initialized succesfully [ 0.697048] host1x host1x: initialized [ 0.698288] CPU PMU: probing PMU on CPU 0 [ 0.698322] hw perfevents: enabled with ARMv7 Cortex-A15 PMU driver, 7 counters available [ 0.698975] tegra_throttle : init passed [ 0.699096] Tegra cpuquiet initialized: disabled [ 0.699230] cpu-tegra: init EDP limit: 2065 MHz [ 0.700225] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type CPU-therm [ 0.700604] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type GPU-therm [ 0.700868] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type MEM-therm [ 0.701113] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.702643] bounce pool size: 64 pages [ 0.704138] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.704433] NTFS driver 2.1.30 [Flags: R/O]. [ 0.704723] fuse init (API version 7.22) [ 0.704961] msgmni has been set to 1457 [ 0.706414] io scheduler noop registered (default) [ 0.706762] of_get_named_gpio_flags: can't parse gpios property [ 0.706773] of_get_named_gpio_flags: can't parse gpios property [ 0.706782] of_get_named_gpio_flags: can't parse gpios property [ 0.907834] PCIE: port 0: link down, retrying [ 1.107898] PCIE: port 0: link down, retrying [ 1.307961] PCIE: port 0: link down, retrying [ 1.307983] PCIE: port 0: link down, ignoring [ 1.313141] PCI host bridge to bus 0000:00 [ 1.313171] pci_bus 0000:00: root bus resource [mem 0x32100000-0x3fffffff] [ 1.313200] pci_bus 0000:00: root bus resource [mem 0x12100000-0x320fffff pref] [ 1.313232] pci_bus 0000:00: root bus resource [io 0x1000-0xffff] [ 1.313259] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.313317] pci 0000:00:00.0: [10de:0e13] type 01 class 0x060400 [ 1.313412] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.313639] PCI: bus0: Fast back to back transfers disabled [ 1.313688] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.313895] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 [ 1.313929] pci 0000:01:00.0: reg 10: [io 0x0000-0x00ff] [ 1.313976] pci 0000:01:00.0: reg 18: [mem 0x00000000-0x00000fff 64bit] [ 1.314008] pci 0000:01:00.0: reg 20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.314111] pci 0000:01:00.0: supports D1 D2 [ 1.314122] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.315716] PCI: bus1: Fast back to back transfers disabled [ 1.315748] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.315765] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 1.316052] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt [ 1.316082] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 1.316111] pcie_pme 0000:00:00.0:pcie01: service driver pcie_pme loaded [ 1.316234] aer 0000:00:00.0:pcie02: service driver aer loaded [ 1.316336] pcieport 0000:00:00.0: BAR 8: assigned [mem 0x32100000-0x321fffff] [ 1.316371] pcieport 0000:00:00.0: BAR 9: assigned [mem 0x12100000-0x121fffff 64bit pref] [ 1.316404] pcieport 0000:00:00.0: BAR 7: assigned [io 0x1000-0x1fff] [ 1.316437] pci 0000:01:00.0: BAR 4: assigned [mem 0x12100000-0x12103fff 64bit pref] [ 1.316484] pci 0000:01:00.0: BAR 2: assigned [mem 0x32100000-0x32100fff 64bit] [ 1.316529] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 1.316561] pcieport 0000:00:00.0: PCI bridge to [bus 01] [ 1.316587] pcieport 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 1.316616] pcieport 0000:00:00.0: bridge window [mem 0x32100000-0x321fffff] [ 1.316648] pcieport 0000:00:00.0: bridge window [mem 0x12100000-0x121fffff 64bit pref] [ 1.316713] PCIE: No Link speed change happened [ 1.317272] pwm-backlight pwm-backlight: unable to request PWM, trying legacy API [ 1.317380] sysedp_create_consumer: unable to create pwm-backlight, no consumer_data for pwm-backlight found [ 1.318266] tsec tsec: initialized [ 1.319791] isp isp.0: initialized [ 1.320774] isp isp.1: initialized [ 1.322311] falcon vic03.0: initialized [ 1.323504] falcon msenc: initialized [ 1.324333] tegradc tegradc.0: DSI: HS clock rate is 464500 [ 1.325778] p,wuxga-10-1 panel dt support not available [ 1.605580] tegradc tegradc.0: nominal-pclk:154700000 parent:154500000 div:1.0 pclk:154500000 153153000~168623000 [ 1.694834] tegradc tegradc.0: DSI pad calibration done [ 1.701982] tegradc tegradc.0: probed [ 1.702454] tegradc tegradc.0: fb registered [ 1.702476] tegradc tegradc.0: nominal-pclk:154679000 parent:463500000 div:3.0 pclk:154500000 153132210~168600110 [ 1.708336] gpio wake4 for gpio=111 [ 1.734448] Reserved SVD code 97 [ 1.734469] Reserved SVD code 96 [ 1.734486] Reserved SVD code 102 [ 1.734503] Reserved SVD code 101 [ 1.734519] Reserved SVD code 95 [ 1.734536] Reserved SVD code 100 [ 1.734552] Reserved SVD code 93 [ 1.734568] Reserved SVD code 98 [ 1.734584] Reserved SVD code 94 [ 1.734600] Reserved SVD code 99 [ 1.736519] tegradc tegradc.1: nominal-pclk:148500000 parent:594000000 div:4.0 pclk:148500000 147015000~161865000 [ 1.737844] tegradc tegradc.1: probed [ 1.759244] Console: switching to colour frame buffer device 240x67 [ 1.778054] tegradc tegradc.1: fb registered [ 1.778166] hdmi_state_machine_worker (tid edb0c080): state 7 (Takeover from bootloader), hpd 1, pending_hpd_evt 1 [ 1.778344] hdmi_state_machine_set_state_l: switching from state 7 (Takeover from bootloader) to state 1 (Check Plug) [ 1.781519] tegra-apbdma tegra-apbdma: Tegra20 APB DMA driver register 32 channels [ 1.782362] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.783802] serial8250.0: ttyS0 at MMIO 0x70006300 (irq = 122) is a Tegra [ 1.819604] hdmi_state_machine_worker (tid edb0c080): state 1 (Check Plug), hpd 1, pending_hpd_evt 0 [ 1.819610] hdmi_state_machine_set_state_l: switching from state 1 (Check Plug) to state 2 (Check EDID) [ 1.891154] hdmi_state_machine_worker (tid edb0c080): state 2 (Check EDID), hpd 1, pending_hpd_evt 0 [ 1.945672] Reserved SVD code 97 [ 1.945675] Reserved SVD code 96 [ 1.945678] Reserved SVD code 102 [ 1.945681] Reserved SVD code 101 [ 1.945683] Reserved SVD code 95 [ 1.945685] Reserved SVD code 100 [ 1.945687] Reserved SVD code 93 [ 1.945689] Reserved SVD code 98 [ 1.945692] Reserved SVD code 94 [ 1.945694] Reserved SVD code 99 [ 1.945724] panel size 0 by 0 [ 4.157757] console [ttyS0] enabled [ 4.158375] serial-tegra.0: ttyTHS0 at MMIO 0x70006000 (irq = 68) is a SERIAL_TEGRA [ 4.158706] serial-tegra.1: ttyTHS1 at MMIO 0x70006040 (irq = 69) is a SERIAL_TEGRA [ 4.159017] serial-tegra.2: ttyTHS2 at MMIO 0x70006200 (irq = 78) is a SERIAL_TEGRA [ 4.165174] loop: module loaded [ 4.165485] nct1008_nct72 0-004c: success in enabling rail vdd_nct72 [ 4.169259] gpio wake35 for gpio=70 [ 4.169334] nct1008_nct72 0-004c: nct1008_probe: initialized [ 4.169983] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type Tboard_tegra [ 4.171019] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type Tdiode_tegra [ 4.173001] tegra_profiler: Branch: Dev [ 4.173004] tegra_profiler: Version: 1.103 [ 4.173008] tegra_profiler: Samples version: 34 [ 4.173011] tegra_profiler: IO version: 18 [ 4.173017] armv7_pmu: arch: Cortex A15, type: 4, ver: 0 [ 4.173205] tegra_profiler: auth: init [ 4.173591] GPS: mt3332_gps_mod_init: platform_driver_register ret = 0 [ 4.174332] tegra-sata tegra-sata.0: version 1.0 [ 4.174342] of_get_named_gpio_flags: can't parse gpios property [ 4.175052] tegra-sata tegra-sata.0: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl TEGRA-SATA mode [ 4.175064] tegra-sata tegra-sata.0: flags: 64bit ncq sntf pm led pmp pio slum part sadm apst [ 4.176270] scsi0 : tegra-sata [ 4.176680] scsi1 : tegra-sata [ 4.176920] ata1: SATA max UDMA/133 irq 55 [ 4.176924] ata2: DUMMY [ 4.178950] tun: Universal TUN/TAP device driver, 1.6 [ 4.178954] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 4.179190] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 4.181503] r8169 0000:01:00.0 eth0: RTL8168g/8111g at 0xf0000000, 00:04:4b:49:18:22, XID 0c000800 IRQ 641 [ 4.181511] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 4.181689] usbcore: registered new interface driver asix [ 4.181737] usbcore: registered new interface driver ax88179_178a [ 4.181773] usbcore: registered new interface driver cdc_ether [ 4.181827] usbcore: registered new interface driver smsc95xx [ 4.181867] usbcore: registered new interface driver cdc_subset [ 4.181941] usbcore: registered new interface driver cdc_ncm [ 4.181959] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.182183] tegra USB phy - inst[1] platform info: [ 4.182186] port_otg: no [ 4.182189] has_hostpc: yes [ 4.182192] phy_interface: USB_PHY_INTF_UTMI [ 4.182194] op_mode: TEGRA_USB_OPMODE_HOST [ 4.182197] qc2_voltage: 0 [ 4.182200] vbus_gpio: -1 [ 4.182203] hot_plug: disabled [ 4.182206] remote_wakeup: enabled [ 4.183772] tegra-ehci tegra-ehci.1: Tegra EHCI Host Controller [ 4.183798] tegra-ehci tegra-ehci.1: new USB bus registered, assigned bus number 1 [ 4.183898] Wake40 for irq=53 [ 4.183901] Wake42 for irq=53 [ 4.183924] tegra-ehci tegra-ehci.1: irq 53, io mem 0x7d004000 [ 4.187865] tegradc tegradc.1: nominal-pclk:148500000 parent:594000000 div:4.0 pclk:148500000 147015000~161865000 [ 4.189699] tegra-ehci tegra-ehci.1: USB 2.0 started, EHCI 1.10 [ 4.189788] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.189795] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.189802] usb usb1: Product: Tegra EHCI Host Controller [ 4.189807] usb usb1: Manufacturer: Linux 3.10.40-gb271e8f ehci_hcd [ 4.189813] usb usb1: SerialNumber: tegra-ehci.1 [ 4.190365] hub 1-0:1.0: USB hub found [ 4.190384] hub 1-0:1.0: 1 port detected [ 4.190780] tegra USB phy - inst[2] platform info: [ 4.190783] port_otg: no [ 4.190786] has_hostpc: yes [ 4.190789] phy_interface: USB_PHY_INTF_UTMI [ 4.190792] op_mode: TEGRA_USB_OPMODE_HOST [ 4.190795] qc2_voltage: 0 [ 4.190797] vbus_gpio: -1 [ 4.190800] hot_plug: disabled [ 4.190803] remote_wakeup: enabled [ 4.192253] tegra-ehci tegra-ehci.2: Tegra EHCI Host Controller [ 4.192277] tegra-ehci tegra-ehci.2: new USB bus registered, assigned bus number 2 [ 4.192364] Wake41 for irq=129 [ 4.192367] Wake43 for irq=129 [ 4.192390] tegra-ehci tegra-ehci.2: irq 129, io mem 0x7d008000 [ 4.197698] tegra-ehci tegra-ehci.2: USB 2.0 started, EHCI 1.10 [ 4.197780] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.197787] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.197793] usb usb2: Product: Tegra EHCI Host Controller [ 4.197799] usb usb2: Manufacturer: Linux 3.10.40-gb271e8f ehci_hcd [ 4.197805] usb usb2: SerialNumber: tegra-ehci.2 [ 4.198320] hub 2-0:1.0: USB hub found [ 4.198339] hub 2-0:1.0: 1 port detected [ 4.198731] ehci-pci: EHCI PCI platform driver [ 4.199001] tegra_xusb_read_usb_calib: usb_calib0 = 0x02048389 [ 4.199249] usbcore: registered new interface driver usb-storage [ 4.199358] usbcore: registered new interface driver usbserial [ 4.199397] usbcore: registered new interface driver option [ 4.199427] usbserial: USB Serial support registered for GSM modem (1-port) [ 4.199530] usbcore: registered new interface driver pl2303 [ 4.199561] usbserial: USB Serial support registered for pl2303 [ 4.199574] Nvidia Tegra High-Speed USB Device Controller driver (Apr 30, 2012) [ 4.199741] tegra USB phy - inst[0] platform info: [ 4.199743] port_otg: yes [ 4.199746] has_hostpc: yes [ 4.199748] phy_interface: USB_PHY_INTF_UTMI [ 4.199751] op_mode: TEGRA_USB_OPMODE_DEVICE [ 4.199753] qc2_voltage: 0 [ 4.199756] vbus_pmu_irq: 0 [ 4.199758] vbus_gpio: -1 [ 4.199760] charging: disabled [ 4.199763] remote_wakeup: disabled [ 4.202565] tegra-udc tegra-udc.0: usb_bat_chg regulator not registered: USB charging will not be enabled [ 4.235133] as3722-rtc as3722-rtc.1: rtc core: registered as3722 as rtc0 [ 4.235141] as3722-rtc as3722-rtc.1: RTC interrupt 449 [ 4.289026] i2c /dev entries driver [ 4.290216] virtual_init [ 4.292348] nvavp nvavp: allocated IOVA at 8ff00000 for AVP os [ 4.293174] tegra_dtv_probe: probing dtv. [ 4.293536] setup_stream: bufsize = 4096, bufnum = 4 [ 4.293537] ar0832_init: ++ [ 4.293922] i2c-core: driver [max77387] using legacy suspend method [ 4.293925] i2c-core: driver [max77387] using legacy resume method [ 4.293973] i2c-core: driver [as364x] using legacy suspend method [ 4.293975] i2c-core: driver [as364x] using legacy resume method [ 4.294126] [IMX135] sensor driver loading [ 4.294174] [IMX179] sensor driver loading [ 4.294220] [IMX185] sensor driver loading [ 4.294269] [imx132] sensor driver loading [ 4.294316] [AR0330] sensor driver loading [ 4.294363] [ar0261] sensor driver loading [ 4.294410] [AR1335] sensor driver loading [ 4.294459] [ov4689] sensor driver loading [ 4.295335] usbcore: registered new interface driver uvcvideo [ 4.295338] USB Video Class driver (1.1.1) [ 4.296244] zram: Created 1 device(s) ... [ 4.297446] tegra_wdt tegra_wdt.0: last reset is due to power on reset [ 4.297615] WDT heartbeat enabled on probe [ 4.297618] tegra_wdt_probe done [ 4.297965] sdhci: Secure Digital Host Controller Interface driver [ 4.297968] sdhci: Copyright(c) Pierre Ossman [ 4.297971] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.298335] sdhci-tegra sdhci-tegra.3: vddio_sd_slot regulator not found: -517. Assuming vddio_sd_slot is not required. [ 4.298494] sdhci-tegra sdhci-tegra.3: Speedo value 2208 [ 4.298502] sdhci-tegra sdhci-tegra.3: Tuning constraints: nom_mv 1150, boot_mv 1150, min_or_mv 1100 [ 4.352694] otg state changed: SUSPEND --> PERIPHERAL [ 4.481713] ata1: SATA link down (SStatus 0 SControl 300) [ 4.505717] usb 2-1: new high-speed USB device number 2 using tegra-ehci [ 4.580824] usb 2-1: New USB device found, idVendor=05e3, idProduct=0608 [ 4.580832] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 4.580839] usb 2-1: Product: USB2.0 Hub [ 4.592207] hub 2-1:1.0: USB hub found [ 4.603794] hub 2-1:1.0: 4 ports detected [ 5.000782] usb 2-1.2: new low-speed USB device number 3 using tegra-ehci [ 5.091764] usb 2-1.2: New USB device found, idVendor=413c, idProduct=2003 [ 5.091771] usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.091778] usb 2-1.2: Product: Dell USB Keyboard [ 5.091784] usb 2-1.2: Manufacturer: Dell [ 5.421610] handle_check_edid_l: audio_switch 1 [ 5.430156] Display connected, hpd_switch 1 [ 5.438355] handle_check_edid_l: setting audio and infoframes [ 5.448172] hdmi_state_machine_set_state_l: switching from state 2 (Check EDID) to state 4 (Enabled) [ 5.461461] hdmi_state_machine_worker (tid edb0c080): state 4 (Enabled), hpd 1, pending_hpd_evt 0 [ 5.475011] mmc0: no vqmmc regulator found [ 5.475028] mmc0: no vmmc regulator found [ 5.475032] mmc0: Invalid maximum block size, assuming 512 bytes [ 5.498697] sysedp_create_consumer: unable to create sdhci-tegra.3, no consumer_data for sdhci-tegra.3 found [ 5.498698] mmc0: SDHCI controller on sdhci-tegra.3 [sdhci-tegra.3] using ADMA [ 5.499625] sdhci-tegra sdhci-tegra.2: Speedo value 2208 [ 5.499634] sdhci-tegra sdhci-tegra.2: Tuning constraints: nom_mv 1150, boot_mv 1150, min_or_mv 1100 [ 5.584621] mmc1: no vqmmc regulator found [ 5.593094] mmc1: no vmmc regulator found [ 5.601434] mmc1: Invalid maximum block size, assuming 512 bytes [ 5.613943] mmc0: BKOPS_EN bit is not set [ 5.619291] sdhci-tegra sdhci-tegra.3: Found T2T coeffs data [ 5.619299] sdhci-tegra sdhci-tegra.3: 200MHz tap hole coeffs found [ 5.611847] sysedp_create_consumer: unable to create sdhci-tegra.2, no consumer_data for sdhci-tegra.2 found [ 5.674706] mmc1: SDHCI controller on sdhci-tegra.2 [sdhci-tegra.2] using ADMA [ 5.691741] gpio wake56 for gpio=170 [ 5.703649] tegra-se tegra12-se: tegra_se_probe: complete [ 5.714185] usb 2-1.3: new low-speed USB device number 4 using tegra-ehci [ 5.731974] input: Dell Dell USB Keyboard as /devices/platform/tegra-ehci.2/usb2/2-1/2-1.2/2-1.2:1.0/input/input0 [ 5.747407] hid-generic 0003:413C:2003.0001: input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-tegra-ehci.2-1.2/input0 [ 5.764268] usbcore: registered new interface driver usbhid [ 5.774914] usbhid: USB HID core driver [ 5.784192] tegra-hier-ictlr tegra-hier-ictlr: probed [ 5.796916] usb 2-1.3: New USB device found, idVendor=1c4f, idProduct=0003 [ 5.808941] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.821342] usb 2-1.3: Product: Usb Mouse [ 5.830440] usb 2-1.3: Manufacturer: SIGMACHIP [ 5.843536] input: SIGMACHIP Usb Mouse as /devices/platform/tegra-ehci.2/usb2/2-1/2-1.3/2-1.3:1.0/input/input1 [ 5.859017] hid-generic 0003:1C4F:0003.0002: input: USB HID v1.10 Mouse [SIGMACHIP Usb Mouse] on usb-tegra-ehci.2-1.3/input0 [ 6.164786] **********Auto tuning windows************* [ 6.164789] WIN_ATTR legend: 0-BOUN_ST, 1-BOUN_END, 2-HOLE [ 6.164800] win[0]: 0(0) - 78(1) [ 6.164804] win[1]: 85(0) - 165(1) [ 6.164808] win[2]: 171(0) - 252(1) [ 6.164811] *************************************** [ 6.164825] ********tuning windows after inserting holes***** [ 6.164828] WIN_ATTR legend: 0-BOUN_ST, 1-BOUN_END, 2-HOLE [ 6.164832] win[0]:-2(0) - 46(2) [ 6.164836] win[1]:48(2) - 78(1) [ 6.164840] win[2]:85(0) - 133(2) [ 6.164844] win[3]:135(2) - 165(1) [ 6.164848] win[4]:171(0) - 220(2) [ 6.164851] win[5]:222(2) - 252(1) [ 6.164854] *********************************************** [ 6.164859] **********Tuning values********* [ 6.164861] **estimated values** [ 6.164866] T2T_Vmax 58, T2T_Vmin 82, 1'st_hole_Vmax 46, UI_Vmax 86 [ 6.164869] **Calculated values** [ 6.164872] T2T_Vmax 57, 1'st_hole_Vmax 47, UI_Vmax 87 [ 6.164876] T2T_Vmin 57, 1'st_hole_Vmin 47, UI_Vmin 87 [ 6.164879] *********************************** [ 6.164885] ***********final tuning windows********** [ 6.164889] win[0]: 15 - 37 [ 6.164892] win[1]: 58 - 61 [ 6.164895] win[2]: 102 - 118 [ 6.164897] win[3]: 151 - 148 [ 6.164900] win[4]: 188 - 199 [ 6.164903] win[5]: 244 - 235 [ 6.164905] ******************************** [ 6.164910] best tap win - (15-37), best tap value 26 prev_best_tap 0 [ 6.420416] usbcore: registered new interface driver snd-usb-audio [ 6.421082] MAX98090 driver built on Oct 13 2017 at 18:03:00 [ 6.425284] tegra_offload_platform probe successfull. [ 6.425289] succefully registered offload ops [ 6.425289] tegra30_avp_audio_platform_probe successful. [ 6.687213] rt5639 0-001c: read 0xfd=0x6 [ 6.708321] **********Auto tuning windows************* [ 6.713789] rt5639 0-001c: ASoC: mux INR Mux has no paths [ 6.713804] rt5639 0-001c: ASoC: mux INL Mux has no paths [ 6.714559] gpio wake49 for gpio=143 [ 6.747702] WIN_ATTR legend: 0-BOUN_ST, 1-BOUN_END, 2-HOLE [ 6.757841] win[0]: 0(0) - 78(1) [ 6.765650] win[1]: 84(0) - 165(1) [ 6.773588] win[2]: 172(0) - 252(1) [ 6.781521] *************************************** [ 6.790898] ********tuning windows after inserting holes***** [ 6.801144] WIN_ATTR legend: 0-BOUN_ST, 1-BOUN_END, 2-HOLE [ 6.811050] win[0]:-3(0) - 46(2) [ 6.818544] win[1]:48(2) - 78(1) [ 6.826017] win[2]:84(0) - 133(2) [ 6.833516] win[3]:135(2) - 165(1) [ 6.841037] win[4]:172(0) - 220(2) [ 6.848495] win[5]:222(2) - 252(1) [ 6.855903] *********************************************** [ 6.865498] **********Tuning values********* [ 6.873694] **estimated values** [ 6.880724] T2T_Vmax 58, T2T_Vmin 82, 1'st_hole_Vmax 46, UI_Vmax 86 [ 6.890759] **Calculated values** [ 6.897841] T2T_Vmax 57, 1'st_hole_Vmax 47, UI_Vmax 87 [ 6.906777] T2T_Vmin 57, 1'st_hole_Vmin 47, UI_Vmin 87 [ 6.915634] *********************************** [ 6.923890] ***********final tuning windows********** [ 6.932608] win[0]: 14 - 37 [ 6.939052] win[1]: 58 - 61 [ 6.945418] win[2]: 101 - 118 [ 6.951817] win[3]: 151 - 148 [ 6.958075] win[4]: 189 - 199 [ 6.964288] win[5]: 244 - 235 [ 6.970486] ******************************** [ 6.978008] best tap win - (14-37), best tap value 26 prev_best_tap 26 [ 6.987873] sdhci-tegra sdhci-tegra.3: sdhci_tegra_verify_best_tap: tuning freq 200000000hz, best tap 26 [ 7.003352] mmc0: new HS200 MMC card at address 0001 [ 7.011966] mmcblk mmc0:0001: Card claimed for testing. [ 7.020885] mmcblk0: mmc0:0001 SEM16G 14.6 GiB [ 7.029067] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB [ 7.041215] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 [ 7.716699] rt5639 0-001c: rt5639_headset_detect RT5639_PWR_ANLG1(0x63) = 0xa814 [ 7.728018] rt5639 0-001c: rt5639_headset_detect RT5639_IRQ_CTRL2(0xbe) = 0x0 [ 7.800942] rt5639 0-001c: rt5639_headset_detect jack_type = 2 [ 7.810839] tegra-snd-rt5639 tegra-snd-rt5639.0: rt5639-aif1 <-> tegra30-i2s.1 mapping ok [ 7.823487] tegra-snd-rt5639 tegra-snd-rt5639.0: dit-hifi <-> tegra30-spdif mapping ok [ 7.836039] tegra-snd-rt5639 tegra-snd-rt5639.0: dit-hifi <-> tegra30-i2s.3 mapping ok [ 7.848497] tegra-snd-rt5639 tegra-snd-rt5639.0: rt5639-aif1 <-> dit-hifi mapping ok [ 7.860809] tegra-snd-rt5639 tegra-snd-rt5639.0: dit-hifi <-> dit-hifi mapping ok [ 7.872710] tegra-snd-rt5639 tegra-snd-rt5639.0: Allocating for stream playback [ 7.883786] tegra-snd-rt5639 tegra-snd-rt5639.0: Allocating for stream capture [ 7.894754] tegra-snd-rt5639 tegra-snd-rt5639.0: snd-soc-dummy-dai <-> tegra-offload-pcm mapping ok [ 7.908198] compress asoc: snd-soc-dummy-dai <-> tegra-offload-compr mapping ok [ 7.919899] tegra-snd-rt5639 tegra-snd-rt5639.0: Allocating for stream playback [ 7.931108] tegra-snd-rt5639 tegra-snd-rt5639.0: Allocating for stream capture [ 7.942228] tegra-snd-rt5639 tegra-snd-rt5639.0: snd-soc-dummy-dai <-> tegra-offload-pcm mapping ok [ 7.955813] tegra-snd-rt5639 tegra-snd-rt5639.0: rt5639-aif1 <-> tegra30-i2s.1 mapping ok [ 7.971748] input: tegra-rt5639 Headphone Jack as /devices/platform/tegra-snd-rt5639.0/sound/card1/input2 [ 7.986418] sysedp_create_consumer: unable to create speaker, no consumer_data for speaker found [ 7.995941] oprofile: using timer interrupt. [ 8.008673] GACT probability NOT on [ 8.016274] Mirror/redirect action on [ 8.024006] u32 classifier [ 8.030760] Actions configured [ 8.038165] Netfilter messages via NETLINK v0.30. [ 8.046976] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 8.057574] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 8.068631] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 8.078872] xt_time: kernel timezone is -0000 [ 8.087631] ip_tables: (C) 2000-2006 Netfilter Core Team [ 8.097236] arp_tables: (C) 2002 David S. Miller [ 8.106053] TCP: cubic registered [ 8.113703] NET: Registered protocol family 10 [ 8.123089] mip6: Mobile IPv6 [ 8.130218] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 8.139929] sit: IPv6 over IPv4 tunneling driver [ 8.149614] NET: Registered protocol family 17 [ 8.158278] NET: Registered protocol family 15 [ 8.166925] NET: Registered protocol family 35 [ 8.175520] NET: Registered protocol family 37 [ 8.184032] NET: Registered protocol family 41 [ 8.193830] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 8.229228] Registering SWP/SWPB emulation handler [ 8.238194] last reset is due to power on reset [ 8.238194] [ 8.252550] Disabling clocks left on by bootloader: [ 8.261590] audio_2x [ 8.268191] audio [ 8.274491] audio4 [ 8.280788] audio3 [ 8.287032] audio2 [ 8.293264] audio1 [ 8.299474] audio0 [ 8.305711] hdmi_audio [ 8.312184] entropy [ 8.318429] dsi2-fixed [ 8.324928] dsi1-fixed [ 8.331415] nor [ 8.337272] trace [ 8.343306] sdmmc4_ddr [ 8.349778] sdmmc3_ddr [ 8.356214] cclk_lp [ 8.362233] pll_x_out0 [ 8.368420] pll_m_out1 [ 8.374712] tegra_dvfs: vdd_cpu connected to regulator [ 8.383454] tegra_dvfs: vdd_core connected to regulator [ 8.392269] tegra_dvfs: vdd_gpu connected to regulator [ 8.402263] cpu_cold cooling device is registered [ 8.410584] cpu_hot cooling device is registered [ 8.410710] Tegra CPU DFLL is initialized with use_dfll = 1 [ 8.410772] CPU rate: 696 MHz [ 8.601158] tegra dvfs: tegra sysfs cap interface is initialized [ 8.610431] tegra dvfs: tegra sysfs gpu & emc interface is initialized [ 8.620868] tegra_actmon.emc: Completed initialization (0) [ 8.629852] tegra_actmon.avp: Completed initialization (0) [ 8.638699] tegra_mon.cpu_emc: Completed initialization (0) [ 8.650507] reg-aon-1v2: incomplete constraints, leaving on [ 8.659419] reg-aon-1v8: incomplete constraints, leaving on [ 8.668319] sdmmc-en-supply: incomplete constraints, leaving on [ 8.677420] reg-dcdc-1v2: incomplete constraints, leaving on [ 8.686349] reg-5v0-supply: incomplete constraints, leaving on [ 8.695474] usb0-vbus: incomplete constraints, leaving on [ 8.704146] vpp-fuse: incomplete constraints, leaving on [ 8.712724] vdd-2v7-cam: incomplete constraints, leaving on [ 8.721509] avdd-spi: incomplete constraints, leaving on [ 8.730069] vdd-1v1-cam: incomplete constraints, leaving on [ 8.738765] vddio-sdmmc-2: incomplete constraints, leaving on [ 8.747643] vdd-1v2-cam: incomplete constraints, leaving on [ 8.756380] avdd-cam: incomplete constraints, leaving on [ 8.764872] vdd-cam: incomplete constraints, leaving on [ 8.773298] as3722-sd3: incomplete constraints, leaving on [ 8.781999] vdd-3v3-aon: incomplete constraints, leaving on [ 8.790780] vdd-ac-bat: incomplete constraints, leaving on [ 8.799450] regulator-dummy: incomplete constraints, leaving on [ 8.809252] of_get_named_gpio_flags exited with status 128 [ 8.809305] gpio wake51 for gpio=128 [ 8.816280] input: gpio-keys.3 as /devices/platform/gpio-keys.3/input/input3 [ 8.827313] as3722-rtc as3722-rtc.1: setting system clock to 2000-01-01 00:46:50 UTC (946687610) [ 8.840253] ALSA device list: [ 8.845906] #0: HDA NVIDIA Tegra at 0x70038000 irq 113 [ 8.853935] #1: tegra-rt5639 [ 8.860710] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities [ 8.872158] EXT4-fs (mmcblk0p1): couldn't mount as ext2 due to feature incompatibilities [ 9.336115] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281197 [ 9.336329] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281199 [ 9.336450] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281200 [ 9.336532] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281191 [ 9.336608] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281109 [ 9.336713] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281142 [ 9.336791] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281140 [ 9.336865] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 280984 [ 9.336942] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281132 [ 9.337023] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281190 [ 9.337097] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281181 [ 9.337177] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 573031 [ 9.337254] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 573030 [ 9.337329] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281146 [ 9.337402] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 573029 [ 9.337479] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 573028 [ 9.337552] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281141 [ 9.337625] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281188 [ 9.337744] EXT4-fs (mmcblk0p1): 18 orphan inodes deleted [ 9.346110] EXT4-fs (mmcblk0p1): recovery complete [ 9.367572] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 9.378728] VFS: Mounted root (ext4 filesystem) on device 179:1. [ 9.397199] devtmpfs: mounted [ 9.403548] Freeing unused kernel memory: 496K (c0b5c000 - c0bd8000) [ 9.649747] init: plymouth-upstart-bridge main process (119) terminated with status 1 [ 9.661936] init: plymouth-upstart-bridge main process ended, respawning [ 9.713826] init: plymouth-upstart-bridge main process (129) terminated with status 1 [ 9.725619] init: plymouth-upstart-bridge main process ended, respawning [ 9.740707] init: ureadahead main process (122) terminated with status 5 [ 9.781501] init: plymouth-upstart-bridge main process (134) terminated with status 1 [ 9.793429] init: plymouth-upstart-bridge main process ended, respawning [ 11.275236] systemd-udevd[304]: starting version 204 [ 11.641636] Tegra cpuquiet clusterswitch enabled [ 11.698472] otg state changed: PERIPHERAL --> SUSPEND [ 11.698716] tegra-udc tegra-udc.0: USB cable/charger disconnected [ 11.699020] otg state changed: SUSPEND --> HOST [ 11.700314] tegra USB phy - inst[0] platform info: [ 11.700340] port_otg: yes [ 11.700353] has_hostpc: yes [ 11.700367] phy_interface: USB_PHY_INTF_UTMI [ 11.700379] op_mode: TEGRA_USB_OPMODE_HOST [ 11.700396] qc2_voltage: 0 [ 11.700413] vbus_gpio: -1 [ 11.700428] hot_plug: disabled [ 11.700446] remote_wakeup: enabled [ 11.758193] vi vi.0: vi_probe: ++ [ 11.777228] vi vi.0: initialized [ 11.778060] vi vi.1: vi_probe: ++ [ 11.780716] vi vi.1: initialized [ 12.026649] Bluetooth: Core ver 2.16 [ 12.032470] NET: Registered protocol family 31 [ 12.032493] Bluetooth: HCI device and connection manager initialized [ 12.032561] Bluetooth: HCI socket layer initialized [ 12.032595] Bluetooth: L2CAP socket layer initialized [ 12.032719] Bluetooth: SCO socket layer initialized [ 12.081222] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 12.081298] Bluetooth: BNEP socket layer initialized [ 12.232942] Bluetooth: RFCOMM socket layer initialized [ 12.232951] Bluetooth: RFCOMM ver 1.11 [ 12.703178] tegra-ehci tegra-ehci.0: Tegra EHCI Host Controller [ 12.703250] tegra-ehci tegra-ehci.0: new USB bus registered, assigned bus number 3 [ 12.703542] tegra-ehci tegra-ehci.0: irq 52, io mem 0x7d000000 [ 12.708741] tegra-ehci tegra-ehci.0: USB 2.0 started, EHCI 1.10 [ 12.708975] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 12.708987] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.708999] usb usb3: Product: Tegra EHCI Host Controller [ 12.709009] usb usb3: Manufacturer: Linux 3.10.40-gb271e8f ehci_hcd [ 12.709020] usb usb3: SerialNumber: tegra-ehci.0 [ 12.710229] hub 3-0:1.0: USB hub found [ 12.710275] hub 3-0:1.0: 1 port detected [ 12.943767] init: udev-fallback-graphics main process (445) terminated with status 1 [ 12.973826] device-mapper: uevent: version 1.0.3 [ 12.974239] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com [ 13.755780] r8169 0000:01:00.0 eth0: link down [ 13.755958] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 14.233279] init: plymouth-upstart-bridge main process ended, respawning [ 14.453542] init: plymouth-stop pre-start process (935) terminated with status 1 [ 15.054766] tegradc tegradc.1: nominal-pclk:148500000 parent:594000000 div:4.0 pclk:148500000 147015000~161865000 [ 15.054871] tegra_dc_hdmi_enable: HDMI clock already configured to target frequency, skipping clk setup. [ 15.357815] init: Failed to obtain startpar-bridge instance: Unknown parameter: INSTANCE [ 16.105153] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d [ 16.118770] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d [ 17.388279] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d [ 17.403913] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d [ 18.385455] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d [ 18.410181] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d [ 18.454199] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d [ 66.058985] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d [ 135.325635] init: plymouth-stop pre-start process (2049) terminated with status 1 [ 180.336348] r8169 0000:01:00.0 eth0: link up [ 180.337125] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 199.266973] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead. [ 5045.728836] tegra_dc_hdmi_irq: start [ 5045.729218] tegra_dc_hdmi_irq: end [ 5045.729985] hdmi_state_machine_worker (tid e9f40040): state 4 (Enabled), hpd 0, pending_hpd_evt 1 [ 5045.730146] hdmi_state_machine_set_state_l: switching from state 4 (Enabled) to state 5 (Wait for HPD reassert) [ 5047.233457] hdmi_state_machine_worker (tid e9f40040): state 5 (Wait for HPD reassert), hpd 0, pending_hpd_evt 0 [ 5047.234078] hdmi_state_machine_set_state_l: switching from state 5 (Wait for HPD reassert) to state 0 (Reset) [ 5047.234320] hdmi_state_machine_worker (tid e9f40040): state 0 (Reset), hpd 0, pending_hpd_evt 0 [ 5047.247342] hdmi_disable_l: audio_switch 0 [ 5047.248308] hdmi_disable_l: hpd_switch 0 [ 5047.256415] HDMI from connected to disconnected [ 5047.266210] hdmi_state_machine_set_state_l: switching from state 0 (Reset) to state 1 (Check Plug) [ 5047.279620] hdmi_state_machine_worker (tid e9f40040): state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [ 5047.279648] hdmi_disable_l: audio_switch 0 [ 5047.279654] hdmi_disable_l: hpd_switch 0 [ 5047.279664] hdmi_state_machine_set_state_l: switching from state 1 (Check Plug) to state 3 (Disabled) [ 5047.323993] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d [ 5047.627150] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d [ 5051.719851] tegra_dc_hdmi_irq: start [ 5051.720510] tegra_dc_hdmi_irq: end [ 5051.721995] hdmi_state_machine_worker (tid e9f40040): state 3 (Disabled), hpd 1, pending_hpd_evt 1 [ 5051.722161] hdmi_state_machine_set_state_l: switching from state 3 (Disabled) to state 0 (Reset) [ 5051.763441] hdmi_state_machine_worker (tid e9f40040): state 0 (Reset), hpd 1, pending_hpd_evt 0 [ 5051.770976] hdmi_disable_l: audio_switch 0 [ 5051.771128] hdmi_disable_l: hpd_switch 0 [ 5051.771291] hdmi_state_machine_set_state_l: switching from state 0 (Reset) to state 1 (Check Plug) [ 5051.783327] hdmi_state_machine_worker (tid e9f40040): state 1 (Check Plug), hpd 1, pending_hpd_evt 0 [ 5051.783429] hdmi_state_machine_set_state_l: switching from state 1 (Check Plug) to state 2 (Check EDID) [ 5051.843465] hdmi_state_machine_worker (tid e9f40040): state 2 (Check EDID), hpd 1, pending_hpd_evt 0 [ 5051.873818] Reserved SVD code 97 [ 5051.873899] Reserved SVD code 96 [ 5051.873952] Reserved SVD code 102 [ 5051.874000] Reserved SVD code 101 [ 5051.874048] Reserved SVD code 95 [ 5051.874093] Reserved SVD code 100 [ 5051.874138] Reserved SVD code 93 [ 5051.874183] Reserved SVD code 98 [ 5051.874229] Reserved SVD code 94 [ 5051.874275] Reserved SVD code 99 [ 5051.874482] panel size 0 by 0 [ 5051.896236] handle_check_edid_l: audio_switch 1 [ 5051.900658] Display connected, hpd_switch 1 [ 5051.912139] hdmi_state_machine_set_state_l: switching from state 2 (Check EDID) to state 4 (Enabled) [ 5051.912260] hdmi_state_machine_worker (tid e9f40040): state 4 (Enabled), hpd 1, pending_hpd_evt 0 [ 5051.915167] tegradc tegradc.1: nominal-pclk:148500000 parent:594000000 div:4.0 pclk:148500000 147015000~161865000 [ 5051.920887] tegra_dc_hdmi_enable: HDMI clock already configured to target frequency, skipping clk setup. [ 5051.992191] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d [ 5052.133642] tegradc tegradc.1: nominal-pclk:148500000 parent:594000000 div:4.0 pclk:148500000 147015000~161865000 [ 5052.133745] tegra_dc_hdmi_enable: HDMI clock already configured to target frequency, skipping clk setup. [ 5052.246912] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d [ 5052.310682] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d [ 5052.350776] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d ubuntu@tegra-ubuntu:~$ [/code]
1. The Jetson TK1 does not have a carrier board.

2. Sync polarities are always negative with all EDIDs tried.

3. dmesg:

ubuntu@tegra-ubuntu:~$ dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.40-gb271e8f (buildbrain@mobile-u64-57) (gcc version 4.5.3 (crosstool-NG hg_unknown@20110628.165246) ) #1 SMP PREEMPT Fri Oct 13 18:07:53 PDT 2017
[ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine: jetson-tk1, model: NVIDIA Tegra124 PM375, serial: 0
[ 0.000000] Truncating memory at 0x80000000 to fit in 32-bit physical address space
[ 0.000000] Found tsec, start=0xf4900000 size=2000000
[ 0.000000] Tegra reserved memory:
[ 0.000000] LP0: f46ff000 - f46ff80f
[ 0.000000] Bootloader framebuffer: 00000000 - 00000000
[ 0.000000] Bootloader framebuffer2: 00000000 - 00000000
[ 0.000000] Framebuffer: f8500000 - f96fffff
[ 0.000000] 2nd Framebuffer: f9700000 - fdefffff
[ 0.000000] Carveout: 00000000 - 00000000
[ 0.000000] Vpr: 00000000 - 00000000
[ 0.000000] Tsec: f4900000 - f68fffff
[ 0.000000] cma: CMA: reserved 16 MiB at ae800000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] On node 0 totalpages: 492288
[ 0.000000] free_area_init_node: node 0, pgdat c0d25c80, node_mem_map c0e09000
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2510 pages used for memmap
[ 0.000000] HighMem zone: 297728 pages, LIFO batch:31
[ 0.000000] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/arch/arm/boot/dts/tegra124-jetson_tk1-pm375-000-c00-00.dts
[ 0.000000] Tegra12: CPU Speedo value 2286, Soc Speedo value 2208, Gpu Speedo value 2064
[ 0.000000] Tegra12: CPU Speedo ID 1, Soc Speedo ID 1, Gpu Speedo ID 1
[ 0.000000] Tegra12: CPU Process ID 1,Soc Process ID 1,Gpu Process ID 1
[ 0.000000] Tegra Revision: A01 SKU: 0x81 CPU Process: 1 Core Process: 1
[ 0.000000] tegra: PLLP fixed rate: 408000000
[ 0.000000] tegra_clk_shared_bus_user_init: c2bus client se left ON
[ 0.000000] tegra_clk_shared_bus_user_init: c4bus client vi left ON
[ 0.000000] Lowering cpu_lp maximum rate from 1350000000 to 1092000000
[ 0.000000] Lowering sbus maximum rate from 420000000 to 384000000
[ 0.000000] Lowering vic03 maximum rate from 900000000 to 828000000
[ 0.000000] Lowering tsec maximum rate from 900000000 to 828000000
[ 0.000000] Lowering msenc maximum rate from 600000000 to 528000000
[ 0.000000] Lowering se maximum rate from 600000000 to 528000000
[ 0.000000] Lowering vde maximum rate from 600000000 to 528000000
[ 0.000000] Lowering host1x maximum rate from 500000000 to 444000000
[ 0.000000] Lowering vi maximum rate from 700000000 to 600000000
[ 0.000000] Lowering isp maximum rate from 700000000 to 600000000
[ 0.000000] Lowering c4bus maximum rate from 700000000 to 600000000
[ 0.000000] Lowering pll_c maximum rate from 1400000000 to 1066000000
[ 0.000000] Lowering pll_c2 maximum rate from 1200000000 to 1066000000
[ 0.000000] Lowering pll_c3 maximum rate from 1200000000 to 1066000000
[ 0.000000] Lowering hdmi maximum rate from 594000000 to 297000000
[ 0.000000] Lowering sdmmc1 maximum rate from 208000000 to 204000000
[ 0.000000] Lowering sdmmc3 maximum rate from 208000000 to 204000000
[ 0.000000] Lowering gbus maximum rate from 1032000000 to 852000000
[ 0.000000] Lowering cpu_g maximum rate from 3000000000 to 2065500000
[ 0.000000] tegra dvfs: VDD_CPU nominal 1260mV, scaling enabled
[ 0.000000] tegra dvfs: VDD_CORE nominal 1150mV, scaling enabled
[ 0.000000] tegra dvfs: VDD_GPU nominal 1200mV, scaling enabled
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] tegra_powergate_init: DONE
[ 0.000000] tegra12_plle_clk_enable: pll_e is already enabled
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c1df3000 s15168 r8192 d13504 u36864
[ 0.000000] pcpu-alloc: s15168 r8192 d13504 u36864 alloc=9*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 490768
[ 0.000000] Kernel command line: console=ttyS0,115200n8 console=tty1 no_console_suspend=1 lp0_vec=2064@0xf46ff000 mem=2015M@2048M memtype=255 ddr_die=2048M@2048M section=256M pmuboard=0x0177:0x0000:0x02:0x43:0x00 tsec=32M@3913M otf_key=c75e5bb91eb3bd947560357b64422f85 usbcore.old_scheme_first=1 core_edp_mv=1150 core_edp_ma=4000 tegraid=40.1.1.0.0 debug_uartport=lsport,3 power_supply=Adapter audio_codec=rt5640 modem_id=0 android.kerneltype=normal fbcon=map:1 commchip_id=0 usb_port_owner_info=0 lane_owner_info=6 emc_max_dvfs=0 touch_id=0@0 board_info=0x0177:0x0000:0x02:0x43:0x00 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait tegraboot=sdmmc gpt
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1923MB = 1923MB total
[ 0.000000] Memory: 1920996k/1920996k available, 142364k reserved, 1190908K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0b5b6f4 (11598 kB)
[ 0.000000] .init : 0xc0b5c000 - 0xc0bd8b40 ( 499 kB)
[ 0.000000] .data : 0xc0bda000 - 0xc0d3efd4 (1428 kB)
[ 0.000000] .bss : 0xc0d3efd4 - 0xc0dd9f0c ( 620 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:960
[ 0.000000] the number of interrupt controllers found is 5
[ 0.000000] Architected local timer running at 12.00MHz (phys).
[ 0.000000] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 2863311536128ns
[ 0.000000] Ignoring duplicate/late registration of read_current_timer delay
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty1] enabled
[ 0.003809] Calibrating delay loop (skipped), value calculated using timer frequency.. lpj=12000
[ 0.003880] pid_max: default: 32768 minimum: 301
[ 0.004180] Mount-cache hash table entries: 512
[ 0.027664] Initializing cgroup subsys debug
[ 0.027710] Initializing cgroup subsys freezer
[ 0.027795] CPU: Testing write buffer coherency: ok
[ 0.027890] ftrace: allocating 33486 entries in 66 pages
[ 0.070299] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.070343] Setting up static identity map for 0xc0824af8 - 0xc0824b94
[ 0.074335] ftrace: Allocated trace_printk buffers
[ 0.082028] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.085033] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.088076] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.088270] Brought up 4 CPUs
[ 0.088334] SMP: Total of 4 processors activated.
[ 0.088352] CPU: All CPU(s) started in SVC mode.
[ 0.089218] devtmpfs: initialized
[ 0.098110] pinctrl core: initialized pinctrl subsystem
[ 0.098436] regulator-dummy: no parameters
[ 0.099140] NET: Registered protocol family 16
[ 0.101494] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.102740] tegra_smmu tegra_smmu: Loaded Tegra IOMMU driver
[ 0.104168] console [pstore-1] enabled
[ 0.104206] ramoops: attached 0x200000@0xf8300000, ecc: 0/0
[ 0.104595] cpuidle: using governor ladder
[ 0.104619] cpuidle: using governor menu
[ 0.108446] ardbeg_camera_auxdata: update camera lookup table.
[ 0.117415] tegra-gpio 6000d000.gpio: Initialising GPIO state 0: name default
[ 0.117824] gpiochip_add: registered GPIOs 0 to 255 on device: tegra-gpio
[ 0.124703] Wake16 for irq=34
[ 0.127198] Wake58 for irq=81
[ 0.127248] Wake41 for irq=129
[ 0.127268] Wake43 for irq=129
[ 0.127315] Wake40 for irq=53
[ 0.127333] Wake42 for irq=53
[ 0.131570] board_info: id:sku:fab:major:minor = 0x0177:0x0000:0x42:0x44:0x00
[ 0.131656] board_info: id:sku:fab:major:minor = 0x0177:0x0000:0x42:0x44:0x00
[ 0.131722] disp1 pclk=154700000
[ 0.131732] disp2 pclk=297000000
[ 0.131741] Selecting UARTD as the debug console
[ 0.131789] The debug console clock name is uartd
[ 0.132215] ardbeg_modem_init: modem_id = 0
[ 0.134890] Clear bootloader IO dpd settings
[ 0.135131] Loading jetson TK1 EMC tables.
[ 0.135381] tegra: pll_m is selected as scalable EMC clock source
[ 0.135425] Lowering emc maximum rate from 1200000000 to 924000000
[ 0.135453] tegra: validated EMC DFS table
[ 0.135585] ardbeg_edp_init: CPU regulator 12500 mA
[ 0.401607] ardbeg_edp_init: GPU regulator 11400 mA
[ 0.402602] swapper/0 isomgr_init(): iso emc max clk=924000KHz
[ 0.402623] swapper/0 isomgr_init(): max_iso_bw=7392000KB<6>[ 0.403007] ardbeg_touch_init init raydium touch
[ 0.403168] Raydium - touch platform_id : 8
[ 0.486093] platform tegradc.0: IOVA linear map 0xf8500000(1200000)
[ 0.489408] platform tegradc.0: IOVA linear map 0xf9700000(4800000)
[ 0.494429] platform tegradc.1: IOVA linear map 0xf8500000(1200000)
[ 0.497741] platform tegradc.1: IOVA linear map 0xf9700000(4800000)
[ 0.498178] FUSE: cp_rev 0 ft_rev 0
[ 0.498356] tegra11_soctherem_oc_int_init(): OC interrupts are not enabled
[ 0.498784] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.498816] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.499054] mc-err: Started MC error interface!
[ 0.509808] bio: create slab <bio-0> at 0
[ 0.511766] reg-fixed-voltage 0.regulator: Consumer c1 does not have device name
[ 0.511804] reg-fixed-voltage 0.regulator: Consumer c2 does not have device name
[ 0.511836] of_get_named_gpio_flags: can't parse gpios property
[ 0.511958] vdd-ac-bat: 8400 mV
[ 0.512097] reg-fixed-voltage 1.regulator: Consumer c1 does not have device name
[ 0.512130] reg-fixed-voltage 1.regulator: Consumer c2 does not have device name
[ 0.512160] of_get_named_gpio_flags: can't parse gpios property
[ 0.512265] vdd-3v3-aon: 3300 mV
[ 0.512417] reg-fixed-voltage 8.regulator: Consumer c1 does not have device name
[ 0.512451] reg-fixed-voltage 8.regulator: Consumer c2 does not have device name
[ 0.512483] reg-fixed-voltage 8.regulator: Consumer c3 does not have device name
[ 0.512519] reg-fixed-voltage 8.regulator: Consumer c6 does not have device name
[ 0.512550] reg-fixed-voltage 8.regulator: Consumer c7 does not have device name
[ 0.512581] reg-fixed-voltage 8.regulator: Consumer c8 does not have device name
[ 0.512611] reg-fixed-voltage 8.regulator: Consumer c9 does not have device name
[ 0.512642] reg-fixed-voltage 8.regulator: Consumer c10 does not have device name
[ 0.512673] reg-fixed-voltage 8.regulator: Consumer c11 does not have device name
[ 0.512704] reg-fixed-voltage 8.regulator: Consumer c12 does not have device name
[ 0.512749] of_get_named_gpio_flags: can't parse gpios property
[ 0.512835] reg-3v3-supply: 3300 mV
[ 0.514489] vgaarb: loaded
[ 0.515125] SCSI subsystem initialized
[ 0.515332] libata version 3.00 loaded.
[ 0.515522] usbcore: registered new interface driver usbfs
[ 0.515588] usbcore: registered new interface driver hub
[ 0.515721] usbcore: registered new device driver usb
[ 0.515952] of_get_named_gpio_flags exited with status 20
[ 0.515992] of_get_named_gpio_flags exited with status 21
[ 0.516411] of_get_named_gpio_flags exited with status 157
[ 0.516429] of_get_named_gpio_flags exited with status 158
[ 0.516660] of_get_named_gpio_flags exited with status 217
[ 0.516676] of_get_named_gpio_flags exited with status 218
[ 0.516908] of_get_named_gpio_flags exited with status 172
[ 0.516926] of_get_named_gpio_flags exited with status 173
[ 0.517183] of_get_named_gpio_flags exited with status 206
[ 0.517200] of_get_named_gpio_flags exited with status 207
[ 0.518611] as3722 4-0040: AS3722 ID: ID1:ID2:ID3 = 0x0c:0x01:0x15
[ 0.518641] as3722 4-0040: Final OTP version 1V21
[ 0.523320] gpiochip_find_base: found new base at 1016
[ 0.523418] gpiochip_add: registered GPIOs 1016 to 1023 on device: as3722-gpio
[ 0.523455] GPIO chip as3722-gpio: created GPIO range 0->7 ==> as3722-pinctrl PIN 0->7
[ 0.523623] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name
[ 0.523684] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name
[ 0.523737] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name
[ 0.523770] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name
[ 0.523803] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name
[ 0.523835] as3722-regulator as3722-regulator.0: Consumer c4 does not have device name
[ 0.523894] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name
[ 0.523926] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name
[ 0.523958] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name
[ 0.523989] as3722-regulator as3722-regulator.0: Consumer c4 does not have device name
[ 0.524020] as3722-regulator as3722-regulator.0: Consumer c5 does not have device name
[ 0.524052] as3722-regulator as3722-regulator.0: Consumer c6 does not have device name
[ 0.524084] as3722-regulator as3722-regulator.0: Consumer c7 does not have device name
[ 0.524168] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name
[ 0.524201] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name
[ 0.524233] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name
[ 0.524265] as3722-regulator as3722-regulator.0: Consumer c4 does not have device name
[ 0.524299] as3722-regulator as3722-regulator.0: Consumer c6 does not have device name
[ 0.524333] as3722-regulator as3722-regulator.0: Consumer c8 does not have device name
[ 0.524364] as3722-regulator as3722-regulator.0: Consumer c9 does not have device name
[ 0.524396] as3722-regulator as3722-regulator.0: Consumer c10 does not have device name
[ 0.524428] as3722-regulator as3722-regulator.0: Consumer c11 does not have device name
[ 0.524460] as3722-regulator as3722-regulator.0: Consumer c12 does not have device name
[ 0.524492] as3722-regulator as3722-regulator.0: Consumer c13 does not have device name
[ 0.524524] as3722-regulator as3722-regulator.0: Consumer c14 does not have device name
[ 0.524556] as3722-regulator as3722-regulator.0: Consumer c15 does not have device name
[ 0.524612] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name
[ 0.524643] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name
[ 0.524698] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name
[ 0.524730] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name
[ 0.524761] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name
[ 0.524792] as3722-regulator as3722-regulator.0: Consumer c4 does not have device name
[ 0.524824] as3722-regulator as3722-regulator.0: Consumer c5 does not have device name
[ 0.524855] as3722-regulator as3722-regulator.0: Consumer c6 does not have device name
[ 0.524887] as3722-regulator as3722-regulator.0: Consumer c7 does not have device name
[ 0.524918] as3722-regulator as3722-regulator.0: Consumer c8 does not have device name
[ 0.524950] as3722-regulator as3722-regulator.0: Consumer c9 does not have device name
[ 0.525008] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name
[ 0.525040] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name
[ 0.525147] as3722-regulator as3722-regulator.0: Consumer c8 does not have device name
[ 0.525181] as3722-regulator as3722-regulator.0: Consumer c9 does not have device name
[ 0.525212] as3722-regulator as3722-regulator.0: Consumer c10 does not have device name
[ 0.525270] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name
[ 0.525320] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name
[ 0.525352] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name
[ 0.525383] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name
[ 0.525439] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name
[ 0.525471] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name
[ 0.525529] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name
[ 0.525584] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name
[ 0.525616] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name
[ 0.525690] as3722-regulator as3722-regulator.0: Consumer c1 does not have device name
[ 0.525722] as3722-regulator as3722-regulator.0: Consumer c2 does not have device name
[ 0.525754] as3722-regulator as3722-regulator.0: Consumer c3 does not have device name
[ 0.526672] vdd-cpu: 650 <--> 1300 mV at 1000 mV 3500 mA
[ 0.527444] vdd-core: applied init 1150000uV constraint
[ 0.528049] vdd-core: 700 <--> 1350 mV at 1150 mV 3500 mA
[ 0.529246] vddio-ddr: at 1350 mV
[ 0.529573] as3722-sd3: no parameters
[ 0.530154] avdd-pll-pex: 1050 mV
[ 0.531385] vdd-1v8: at 1800 mV
[ 0.531745] vdd-gpu: applied init 1000000uV constraint
[ 0.532625] vdd-gpu: 650 <--> 1200 mV at 1000 mV 3500 mA
[ 0.533129] avdd-pll: at 1050 mV at 300 mA
[ 0.534417] vdd-cam: 1800 mV at 150 mA
[ 0.535088] avdd-dsi-csi: at 1200 mV at 150 mA
[ 0.536314] vdd-rtc: 800 mV at 150 mA
[ 0.536790] avdd-cam: 2800 mV at 150 mA
[ 0.537299] vdd-1v2-cam: 1175 mV at 150 mA
[ 0.537672] vddio-sdmmc-2: 1800 <--> 3300 mV at 150 mA
[ 0.538172] vdd-1v1-cam: 1275 mV at 150 mA
[ 0.539147] avdd-spi: 3300 mV at 150 mA
[ 0.539668] vdd-2v7-cam: 2800 mV at 150 mA
[ 0.540176] vpp-fuse: 1800 mV at 150 mA
[ 0.540794] of_get_named_gpio_flags: can't parse gpios property
[ 0.540805] of_get_named_gpio_flags: can't parse gpios property
[ 0.541282] Linux video capture interface: v2.00
[ 0.542433] Advanced Linux Sound Architecture Driver Initialized.
[ 0.542880] ardbeg_wifi_power: 1
[ 0.643261] of_get_named_gpio_flags exited with status 108
[ 0.643391] usb0-vbus: 5000 mV
[ 0.643577] of_get_named_gpio_flags exited with status 109
[ 0.643699] usb1-usb2-vbus: 5000 mV
[ 0.643879] of_get_named_gpio_flags exited with status 86
[ 0.643989] vdd-hdmi: 5000 mV
[ 0.644182] of_get_named_gpio_flags exited with status 63
[ 0.644294] avdd-hdmi-pll: 3300 mV
[ 0.644345] avdd-hdmi-pll: supplied by avdd-pll-pex
[ 0.644515] reg-fixed-sync-voltage 6.regulator: Consumer c1 does not have device name
[ 0.644559] of_get_named_gpio_flags exited with status 122
[ 0.644660] vdd-lcd-bl: 3300 mV
[ 0.644819] reg-fixed-sync-voltage 7.regulator: Consumer c1 does not have device name
[ 0.644863] of_get_named_gpio_flags exited with status 58
[ 0.644972] vdd-lcd-bl-en: 5000 mV
[ 0.645149] reg-fixed-sync-voltage 9.regulator: Consumer c3 does not have device name
[ 0.645180] of_get_named_gpio_flags: can't parse gpios property
[ 0.645269] reg-5v0-supply: 5000 mV
[ 0.645436] reg-fixed-sync-voltage a.regulator: Consumer c1 does not have device name
[ 0.645470] reg-fixed-sync-voltage a.regulator: Consumer c2 does not have device name
[ 0.645502] reg-fixed-sync-voltage a.regulator: Consumer c3 does not have device name
[ 0.645551] reg-fixed-sync-voltage a.regulator: Consumer c10 does not have device name
[ 0.645584] reg-fixed-sync-voltage a.regulator: Consumer c11 does not have device name
[ 0.645615] reg-fixed-sync-voltage a.regulator: Consumer c12 does not have device name
[ 0.645647] reg-fixed-sync-voltage a.regulator: Consumer c13 does not have device name
[ 0.645678] reg-fixed-sync-voltage a.regulator: Consumer c14 does not have device name
[ 0.645710] reg-fixed-sync-voltage a.regulator: Consumer c15 does not have device name
[ 0.645765] of_get_named_gpio_flags: can't parse gpios property
[ 0.645854] reg-1v8-supply: 1800 mV
[ 0.646197] reg-fixed-sync-voltage b.regulator: Consumer c1 does not have device name
[ 0.646242] of_get_named_gpio_flags exited with status 138
[ 0.646351] reg-dcdc-1v2: 1200 mV
[ 0.646531] reg-fixed-sync-voltage c.regulator: Consumer c7 does not have device name
[ 0.646565] reg-fixed-sync-voltage c.regulator: Consumer c8 does not have device name
[ 0.646609] of_get_named_gpio_flags exited with status 1018
[ 0.647158] as3722-gpio2-supply: 3300 mV
[ 0.647363] reg-fixed-sync-voltage d.regulator: Consumer c1 does not have device name
[ 0.647409] of_get_named_gpio_flags exited with status 1020
[ 0.647885] as3722-gpio4-supply: 3300 mV
[ 0.648060] of_get_named_gpio_flags exited with status 136
[ 0.648197] sdmmc-en-supply: 3300 mV
[ 0.648370] of_get_named_gpio_flags exited with status 138
[ 0.648462] vdd-cdc-1v2-aud: 1200 mV
[ 0.648619] reg-fixed-sync-voltage 10.regulator: Consumer c1 does not have device name
[ 0.648654] reg-fixed-sync-voltage 10.regulator: Consumer c2 does not have device name
[ 0.648687] reg-fixed-sync-voltage 10.regulator: Consumer c3 does not have device name
[ 0.648717] of_get_named_gpio_flags: can't parse gpios property
[ 0.648811] reg-aon-1v8: 1800 mV
[ 0.648975] reg-fixed-sync-voltage 11.regulator: Consumer c1 does not have device name
[ 0.649007] of_get_named_gpio_flags: can't parse gpios property
[ 0.649102] reg-aon-1v2: 1200 mV
[ 0.652139] as3722-adc-extcon as3722-adc-extcon.2: USB-Host is disconnected
[ 0.655541] tegra: started io power detection dynamic control
[ 0.655568] tegra: NO_IO_POWER setting 0x0
[ 0.655595] Switching to clocksource arch_sys_counter
[ 0.677047] nvmap_heap_init: nvmap_heap_init: created heap block cache
[ 0.677239] nvmap_page_pool_init: Total MB RAM: 1891
[ 0.677264] nvmap_page_pool_init: nvmap page pool size: 60543 pages (236 MB)
[ 0.677422] nvmap_background_zero_thread: PP zeroing thread starting.
[ 0.677593] iram: dma coherent mem declare 0x40001000,258048
[ 0.678437] misc nvmap: created heap iram base 0x40001000 size (252KiB)
[ 0.678602] nvmap:inner cache maint threshold=2097152
[ 0.688550] Wake39 for irq=52
[ 0.688648] tegra-otg tegra-otg: otg transceiver registered
[ 0.689030] NET: Registered protocol family 2
[ 0.689706] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.689914] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.690117] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.690179] TCP: reno registered
[ 0.690205] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.690262] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.690552] NET: Registered protocol family 1
[ 0.690961] RPC: Registered named UNIX socket transport module.
[ 0.690988] RPC: Registered udp transport module.
[ 0.691009] RPC: Registered tcp transport module.
[ 0.691029] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.691056] PCI: CLS 0 bytes, default 64
[ 0.691318] tegra-fuse tegra-fuse: Fuse driver initialized succesfully
[ 0.697048] host1x host1x: initialized
[ 0.698288] CPU PMU: probing PMU on CPU 0
[ 0.698322] hw perfevents: enabled with ARMv7 Cortex-A15 PMU driver, 7 counters available
[ 0.698975] tegra_throttle : init passed
[ 0.699096] Tegra cpuquiet initialized: disabled
[ 0.699230] cpu-tegra: init EDP limit: 2065 MHz
[ 0.700225] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type CPU-therm
[ 0.700604] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type GPU-therm
[ 0.700868] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type MEM-therm
[ 0.701113] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm
[ 0.702643] bounce pool size: 64 pages
[ 0.704138] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.704433] NTFS driver 2.1.30 [Flags: R/O].
[ 0.704723] fuse init (API version 7.22)
[ 0.704961] msgmni has been set to 1457
[ 0.706414] io scheduler noop registered (default)
[ 0.706762] of_get_named_gpio_flags: can't parse gpios property
[ 0.706773] of_get_named_gpio_flags: can't parse gpios property
[ 0.706782] of_get_named_gpio_flags: can't parse gpios property
[ 0.907834] PCIE: port 0: link down, retrying
[ 1.107898] PCIE: port 0: link down, retrying
[ 1.307961] PCIE: port 0: link down, retrying
[ 1.307983] PCIE: port 0: link down, ignoring
[ 1.313141] PCI host bridge to bus 0000:00
[ 1.313171] pci_bus 0000:00: root bus resource [mem 0x32100000-0x3fffffff]
[ 1.313200] pci_bus 0000:00: root bus resource [mem 0x12100000-0x320fffff pref]
[ 1.313232] pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
[ 1.313259] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.313317] pci 0000:00:00.0: [10de:0e13] type 01 class 0x060400
[ 1.313412] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.313639] PCI: bus0: Fast back to back transfers disabled
[ 1.313688] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.313895] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000
[ 1.313929] pci 0000:01:00.0: reg 10: [io 0x0000-0x00ff]
[ 1.313976] pci 0000:01:00.0: reg 18: [mem 0x00000000-0x00000fff 64bit]
[ 1.314008] pci 0000:01:00.0: reg 20: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.314111] pci 0000:01:00.0: supports D1 D2
[ 1.314122] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.315716] PCI: bus1: Fast back to back transfers disabled
[ 1.315748] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.315765] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 1.316052] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
[ 1.316082] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 1.316111] pcie_pme 0000:00:00.0:pcie01: service driver pcie_pme loaded
[ 1.316234] aer 0000:00:00.0:pcie02: service driver aer loaded
[ 1.316336] pcieport 0000:00:00.0: BAR 8: assigned [mem 0x32100000-0x321fffff]
[ 1.316371] pcieport 0000:00:00.0: BAR 9: assigned [mem 0x12100000-0x121fffff 64bit pref]
[ 1.316404] pcieport 0000:00:00.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 1.316437] pci 0000:01:00.0: BAR 4: assigned [mem 0x12100000-0x12103fff 64bit pref]
[ 1.316484] pci 0000:01:00.0: BAR 2: assigned [mem 0x32100000-0x32100fff 64bit]
[ 1.316529] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff]
[ 1.316561] pcieport 0000:00:00.0: PCI bridge to [bus 01]
[ 1.316587] pcieport 0000:00:00.0: bridge window [io 0x1000-0x1fff]
[ 1.316616] pcieport 0000:00:00.0: bridge window [mem 0x32100000-0x321fffff]
[ 1.316648] pcieport 0000:00:00.0: bridge window [mem 0x12100000-0x121fffff 64bit pref]
[ 1.316713] PCIE: No Link speed change happened
[ 1.317272] pwm-backlight pwm-backlight: unable to request PWM, trying legacy API
[ 1.317380] sysedp_create_consumer: unable to create pwm-backlight, no consumer_data for pwm-backlight found
[ 1.318266] tsec tsec: initialized
[ 1.319791] isp isp.0: initialized
[ 1.320774] isp isp.1: initialized
[ 1.322311] falcon vic03.0: initialized
[ 1.323504] falcon msenc: initialized
[ 1.324333] tegradc tegradc.0: DSI: HS clock rate is 464500
[ 1.325778] p,wuxga-10-1 panel dt support not available
[ 1.605580] tegradc tegradc.0: nominal-pclk:154700000 parent:154500000 div:1.0 pclk:154500000 153153000~168623000
[ 1.694834] tegradc tegradc.0: DSI pad calibration done
[ 1.701982] tegradc tegradc.0: probed
[ 1.702454] tegradc tegradc.0: fb registered
[ 1.702476] tegradc tegradc.0: nominal-pclk:154679000 parent:463500000 div:3.0 pclk:154500000 153132210~168600110
[ 1.708336] gpio wake4 for gpio=111
[ 1.734448] Reserved SVD code 97
[ 1.734469] Reserved SVD code 96
[ 1.734486] Reserved SVD code 102
[ 1.734503] Reserved SVD code 101
[ 1.734519] Reserved SVD code 95
[ 1.734536] Reserved SVD code 100
[ 1.734552] Reserved SVD code 93
[ 1.734568] Reserved SVD code 98
[ 1.734584] Reserved SVD code 94
[ 1.734600] Reserved SVD code 99
[ 1.736519] tegradc tegradc.1: nominal-pclk:148500000 parent:594000000 div:4.0 pclk:148500000 147015000~161865000
[ 1.737844] tegradc tegradc.1: probed
[ 1.759244] Console: switching to colour frame buffer device 240x67
[ 1.778054] tegradc tegradc.1: fb registered
[ 1.778166] hdmi_state_machine_worker (tid edb0c080): state 7 (Takeover from bootloader), hpd 1, pending_hpd_evt 1
[ 1.778344] hdmi_state_machine_set_state_l: switching from state 7 (Takeover from bootloader) to state 1 (Check Plug)
[ 1.781519] tegra-apbdma tegra-apbdma: Tegra20 APB DMA driver register 32 channels
[ 1.782362] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.783802] serial8250.0: ttyS0 at MMIO 0x70006300 (irq = 122) is a Tegra
[ 1.819604] hdmi_state_machine_worker (tid edb0c080): state 1 (Check Plug), hpd 1, pending_hpd_evt 0
[ 1.819610] hdmi_state_machine_set_state_l: switching from state 1 (Check Plug) to state 2 (Check EDID)
[ 1.891154] hdmi_state_machine_worker (tid edb0c080): state 2 (Check EDID), hpd 1, pending_hpd_evt 0
[ 1.945672] Reserved SVD code 97
[ 1.945675] Reserved SVD code 96
[ 1.945678] Reserved SVD code 102
[ 1.945681] Reserved SVD code 101
[ 1.945683] Reserved SVD code 95
[ 1.945685] Reserved SVD code 100
[ 1.945687] Reserved SVD code 93
[ 1.945689] Reserved SVD code 98
[ 1.945692] Reserved SVD code 94
[ 1.945694] Reserved SVD code 99
[ 1.945724] panel size 0 by 0
[ 4.157757] console [ttyS0] enabled
[ 4.158375] serial-tegra.0: ttyTHS0 at MMIO 0x70006000 (irq = 68) is a SERIAL_TEGRA
[ 4.158706] serial-tegra.1: ttyTHS1 at MMIO 0x70006040 (irq = 69) is a SERIAL_TEGRA
[ 4.159017] serial-tegra.2: ttyTHS2 at MMIO 0x70006200 (irq = 78) is a SERIAL_TEGRA
[ 4.165174] loop: module loaded
[ 4.165485] nct1008_nct72 0-004c: success in enabling rail vdd_nct72
[ 4.169259] gpio wake35 for gpio=70
[ 4.169334] nct1008_nct72 0-004c: nct1008_probe: initialized
[ 4.169983] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type Tboard_tegra
[ 4.171019] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type Tdiode_tegra
[ 4.173001] tegra_profiler: Branch: Dev
[ 4.173004] tegra_profiler: Version: 1.103
[ 4.173008] tegra_profiler: Samples version: 34
[ 4.173011] tegra_profiler: IO version: 18
[ 4.173017] armv7_pmu: arch: Cortex A15, type: 4, ver: 0
[ 4.173205] tegra_profiler: auth: init
[ 4.173591] GPS: mt3332_gps_mod_init: platform_driver_register ret = 0
[ 4.174332] tegra-sata tegra-sata.0: version 1.0
[ 4.174342] of_get_named_gpio_flags: can't parse gpios property
[ 4.175052] tegra-sata tegra-sata.0: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl TEGRA-SATA mode
[ 4.175064] tegra-sata tegra-sata.0: flags: 64bit ncq sntf pm led pmp pio slum part sadm apst
[ 4.176270] scsi0 : tegra-sata
[ 4.176680] scsi1 : tegra-sata
[ 4.176920] ata1: SATA max UDMA/133 irq 55
[ 4.176924] ata2: DUMMY
[ 4.178950] tun: Universal TUN/TAP device driver, 1.6
[ 4.178954] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 4.179190] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 4.181503] r8169 0000:01:00.0 eth0: RTL8168g/8111g at 0xf0000000, 00:04:4b:49:18:22, XID 0c000800 IRQ 641
[ 4.181511] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 4.181689] usbcore: registered new interface driver asix
[ 4.181737] usbcore: registered new interface driver ax88179_178a
[ 4.181773] usbcore: registered new interface driver cdc_ether
[ 4.181827] usbcore: registered new interface driver smsc95xx
[ 4.181867] usbcore: registered new interface driver cdc_subset
[ 4.181941] usbcore: registered new interface driver cdc_ncm
[ 4.181959] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.182183] tegra USB phy - inst[1] platform info:
[ 4.182186] port_otg: no
[ 4.182189] has_hostpc: yes
[ 4.182192] phy_interface: USB_PHY_INTF_UTMI
[ 4.182194] op_mode: TEGRA_USB_OPMODE_HOST
[ 4.182197] qc2_voltage: 0
[ 4.182200] vbus_gpio: -1
[ 4.182203] hot_plug: disabled
[ 4.182206] remote_wakeup: enabled
[ 4.183772] tegra-ehci tegra-ehci.1: Tegra EHCI Host Controller
[ 4.183798] tegra-ehci tegra-ehci.1: new USB bus registered, assigned bus number 1
[ 4.183898] Wake40 for irq=53
[ 4.183901] Wake42 for irq=53
[ 4.183924] tegra-ehci tegra-ehci.1: irq 53, io mem 0x7d004000
[ 4.187865] tegradc tegradc.1: nominal-pclk:148500000 parent:594000000 div:4.0 pclk:148500000 147015000~161865000
[ 4.189699] tegra-ehci tegra-ehci.1: USB 2.0 started, EHCI 1.10
[ 4.189788] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.189795] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.189802] usb usb1: Product: Tegra EHCI Host Controller
[ 4.189807] usb usb1: Manufacturer: Linux 3.10.40-gb271e8f ehci_hcd
[ 4.189813] usb usb1: SerialNumber: tegra-ehci.1
[ 4.190365] hub 1-0:1.0: USB hub found
[ 4.190384] hub 1-0:1.0: 1 port detected
[ 4.190780] tegra USB phy - inst[2] platform info:
[ 4.190783] port_otg: no
[ 4.190786] has_hostpc: yes
[ 4.190789] phy_interface: USB_PHY_INTF_UTMI
[ 4.190792] op_mode: TEGRA_USB_OPMODE_HOST
[ 4.190795] qc2_voltage: 0
[ 4.190797] vbus_gpio: -1
[ 4.190800] hot_plug: disabled
[ 4.190803] remote_wakeup: enabled
[ 4.192253] tegra-ehci tegra-ehci.2: Tegra EHCI Host Controller
[ 4.192277] tegra-ehci tegra-ehci.2: new USB bus registered, assigned bus number 2
[ 4.192364] Wake41 for irq=129
[ 4.192367] Wake43 for irq=129
[ 4.192390] tegra-ehci tegra-ehci.2: irq 129, io mem 0x7d008000
[ 4.197698] tegra-ehci tegra-ehci.2: USB 2.0 started, EHCI 1.10
[ 4.197780] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.197787] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.197793] usb usb2: Product: Tegra EHCI Host Controller
[ 4.197799] usb usb2: Manufacturer: Linux 3.10.40-gb271e8f ehci_hcd
[ 4.197805] usb usb2: SerialNumber: tegra-ehci.2
[ 4.198320] hub 2-0:1.0: USB hub found
[ 4.198339] hub 2-0:1.0: 1 port detected
[ 4.198731] ehci-pci: EHCI PCI platform driver
[ 4.199001] tegra_xusb_read_usb_calib: usb_calib0 = 0x02048389
[ 4.199249] usbcore: registered new interface driver usb-storage
[ 4.199358] usbcore: registered new interface driver usbserial
[ 4.199397] usbcore: registered new interface driver option
[ 4.199427] usbserial: USB Serial support registered for GSM modem (1-port)
[ 4.199530] usbcore: registered new interface driver pl2303
[ 4.199561] usbserial: USB Serial support registered for pl2303
[ 4.199574] Nvidia Tegra High-Speed USB Device Controller driver (Apr 30, 2012)
[ 4.199741] tegra USB phy - inst[0] platform info:
[ 4.199743] port_otg: yes
[ 4.199746] has_hostpc: yes
[ 4.199748] phy_interface: USB_PHY_INTF_UTMI
[ 4.199751] op_mode: TEGRA_USB_OPMODE_DEVICE
[ 4.199753] qc2_voltage: 0
[ 4.199756] vbus_pmu_irq: 0
[ 4.199758] vbus_gpio: -1
[ 4.199760] charging: disabled
[ 4.199763] remote_wakeup: disabled
[ 4.202565] tegra-udc tegra-udc.0: usb_bat_chg regulator not registered: USB charging will not be enabled
[ 4.235133] as3722-rtc as3722-rtc.1: rtc core: registered as3722 as rtc0
[ 4.235141] as3722-rtc as3722-rtc.1: RTC interrupt 449
[ 4.289026] i2c /dev entries driver
[ 4.290216] virtual_init
[ 4.292348] nvavp nvavp: allocated IOVA at 8ff00000 for AVP os
[ 4.293174] tegra_dtv_probe: probing dtv.
[ 4.293536] setup_stream: bufsize = 4096, bufnum = 4
[ 4.293537] ar0832_init: ++
[ 4.293922] i2c-core: driver [max77387] using legacy suspend method
[ 4.293925] i2c-core: driver [max77387] using legacy resume method
[ 4.293973] i2c-core: driver [as364x] using legacy suspend method
[ 4.293975] i2c-core: driver [as364x] using legacy resume method
[ 4.294126] [IMX135] sensor driver loading
[ 4.294174] [IMX179] sensor driver loading
[ 4.294220] [IMX185] sensor driver loading
[ 4.294269] [imx132] sensor driver loading
[ 4.294316] [AR0330] sensor driver loading
[ 4.294363] [ar0261] sensor driver loading
[ 4.294410] [AR1335] sensor driver loading
[ 4.294459] [ov4689] sensor driver loading
[ 4.295335] usbcore: registered new interface driver uvcvideo
[ 4.295338] USB Video Class driver (1.1.1)
[ 4.296244] zram: Created 1 device(s) ...
[ 4.297446] tegra_wdt tegra_wdt.0: last reset is due to power on reset
[ 4.297615] WDT heartbeat enabled on probe
[ 4.297618] tegra_wdt_probe done
[ 4.297965] sdhci: Secure Digital Host Controller Interface driver
[ 4.297968] sdhci: Copyright(c) Pierre Ossman
[ 4.297971] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.298335] sdhci-tegra sdhci-tegra.3: vddio_sd_slot regulator not found: -517. Assuming vddio_sd_slot is not required.
[ 4.298494] sdhci-tegra sdhci-tegra.3: Speedo value 2208
[ 4.298502] sdhci-tegra sdhci-tegra.3: Tuning constraints: nom_mv 1150, boot_mv 1150, min_or_mv 1100
[ 4.352694] otg state changed: SUSPEND --> PERIPHERAL
[ 4.481713] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.505717] usb 2-1: new high-speed USB device number 2 using tegra-ehci
[ 4.580824] usb 2-1: New USB device found, idVendor=05e3, idProduct=0608
[ 4.580832] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 4.580839] usb 2-1: Product: USB2.0 Hub
[ 4.592207] hub 2-1:1.0: USB hub found
[ 4.603794] hub 2-1:1.0: 4 ports detected
[ 5.000782] usb 2-1.2: new low-speed USB device number 3 using tegra-ehci
[ 5.091764] usb 2-1.2: New USB device found, idVendor=413c, idProduct=2003
[ 5.091771] usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.091778] usb 2-1.2: Product: Dell USB Keyboard
[ 5.091784] usb 2-1.2: Manufacturer: Dell
[ 5.421610] handle_check_edid_l: audio_switch 1
[ 5.430156] Display connected, hpd_switch 1
[ 5.438355] handle_check_edid_l: setting audio and infoframes
[ 5.448172] hdmi_state_machine_set_state_l: switching from state 2 (Check EDID) to state 4 (Enabled)
[ 5.461461] hdmi_state_machine_worker (tid edb0c080): state 4 (Enabled), hpd 1, pending_hpd_evt 0
[ 5.475011] mmc0: no vqmmc regulator found
[ 5.475028] mmc0: no vmmc regulator found
[ 5.475032] mmc0: Invalid maximum block size, assuming 512 bytes
[ 5.498697] sysedp_create_consumer: unable to create sdhci-tegra.3, no consumer_data for sdhci-tegra.3 found
[ 5.498698] mmc0: SDHCI controller on sdhci-tegra.3 [sdhci-tegra.3] using ADMA
[ 5.499625] sdhci-tegra sdhci-tegra.2: Speedo value 2208
[ 5.499634] sdhci-tegra sdhci-tegra.2: Tuning constraints: nom_mv 1150, boot_mv 1150, min_or_mv 1100
[ 5.584621] mmc1: no vqmmc regulator found
[ 5.593094] mmc1: no vmmc regulator found
[ 5.601434] mmc1: Invalid maximum block size, assuming 512 bytes
[ 5.613943] mmc0: BKOPS_EN bit is not set
[ 5.619291] sdhci-tegra sdhci-tegra.3: Found T2T coeffs data
[ 5.619299] sdhci-tegra sdhci-tegra.3: 200MHz tap hole coeffs found
[ 5.611847] sysedp_create_consumer: unable to create sdhci-tegra.2, no consumer_data for sdhci-tegra.2 found
[ 5.674706] mmc1: SDHCI controller on sdhci-tegra.2 [sdhci-tegra.2] using ADMA
[ 5.691741] gpio wake56 for gpio=170
[ 5.703649] tegra-se tegra12-se: tegra_se_probe: complete
[ 5.714185] usb 2-1.3: new low-speed USB device number 4 using tegra-ehci
[ 5.731974] input: Dell Dell USB Keyboard as /devices/platform/tegra-ehci.2/usb2/2-1/2-1.2/2-1.2:1.0/input/input0
[ 5.747407] hid-generic 0003:413C:2003.0001: input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-tegra-ehci.2-1.2/input0
[ 5.764268] usbcore: registered new interface driver usbhid
[ 5.774914] usbhid: USB HID core driver
[ 5.784192] tegra-hier-ictlr tegra-hier-ictlr: probed
[ 5.796916] usb 2-1.3: New USB device found, idVendor=1c4f, idProduct=0003
[ 5.808941] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.821342] usb 2-1.3: Product: Usb Mouse
[ 5.830440] usb 2-1.3: Manufacturer: SIGMACHIP
[ 5.843536] input: SIGMACHIP Usb Mouse as /devices/platform/tegra-ehci.2/usb2/2-1/2-1.3/2-1.3:1.0/input/input1
[ 5.859017] hid-generic 0003:1C4F:0003.0002: input: USB HID v1.10 Mouse [SIGMACHIP Usb Mouse] on usb-tegra-ehci.2-1.3/input0
[ 6.164786] **********Auto tuning windows*************
[ 6.164789] WIN_ATTR legend: 0-BOUN_ST, 1-BOUN_END, 2-HOLE
[ 6.164800] win[0]: 0(0) - 78(1)
[ 6.164804] win[1]: 85(0) - 165(1)
[ 6.164808] win[2]: 171(0) - 252(1)
[ 6.164811] ***************************************
[ 6.164825] ********tuning windows after inserting holes*****
[ 6.164828] WIN_ATTR legend: 0-BOUN_ST, 1-BOUN_END, 2-HOLE
[ 6.164832] win[0]:-2(0) - 46(2)
[ 6.164836] win[1]:48(2) - 78(1)
[ 6.164840] win[2]:85(0) - 133(2)
[ 6.164844] win[3]:135(2) - 165(1)
[ 6.164848] win[4]:171(0) - 220(2)
[ 6.164851] win[5]:222(2) - 252(1)
[ 6.164854] ***********************************************
[ 6.164859] **********Tuning values*********
[ 6.164861] **estimated values**
[ 6.164866] T2T_Vmax 58, T2T_Vmin 82, 1'st_hole_Vmax 46, UI_Vmax 86
[ 6.164869] **Calculated values**
[ 6.164872] T2T_Vmax 57, 1'st_hole_Vmax 47, UI_Vmax 87
[ 6.164876] T2T_Vmin 57, 1'st_hole_Vmin 47, UI_Vmin 87
[ 6.164879] ***********************************
[ 6.164885] ***********final tuning windows**********
[ 6.164889] win[0]: 15 - 37
[ 6.164892] win[1]: 58 - 61
[ 6.164895] win[2]: 102 - 118
[ 6.164897] win[3]: 151 - 148
[ 6.164900] win[4]: 188 - 199
[ 6.164903] win[5]: 244 - 235
[ 6.164905] ********************************
[ 6.164910] best tap win - (15-37), best tap value 26 prev_best_tap 0
[ 6.420416] usbcore: registered new interface driver snd-usb-audio
[ 6.421082] MAX98090 driver built on Oct 13 2017 at 18:03:00
[ 6.425284] tegra_offload_platform probe successfull.
[ 6.425289] succefully registered offload ops
[ 6.425289] tegra30_avp_audio_platform_probe successful.
[ 6.687213] rt5639 0-001c: read 0xfd=0x6
[ 6.708321] **********Auto tuning windows*************
[ 6.713789] rt5639 0-001c: ASoC: mux INR Mux has no paths
[ 6.713804] rt5639 0-001c: ASoC: mux INL Mux has no paths
[ 6.714559] gpio wake49 for gpio=143
[ 6.747702] WIN_ATTR legend: 0-BOUN_ST, 1-BOUN_END, 2-HOLE
[ 6.757841] win[0]: 0(0) - 78(1)
[ 6.765650] win[1]: 84(0) - 165(1)
[ 6.773588] win[2]: 172(0) - 252(1)
[ 6.781521] ***************************************
[ 6.790898] ********tuning windows after inserting holes*****
[ 6.801144] WIN_ATTR legend: 0-BOUN_ST, 1-BOUN_END, 2-HOLE
[ 6.811050] win[0]:-3(0) - 46(2)
[ 6.818544] win[1]:48(2) - 78(1)
[ 6.826017] win[2]:84(0) - 133(2)
[ 6.833516] win[3]:135(2) - 165(1)
[ 6.841037] win[4]:172(0) - 220(2)
[ 6.848495] win[5]:222(2) - 252(1)
[ 6.855903] ***********************************************
[ 6.865498] **********Tuning values*********
[ 6.873694] **estimated values**
[ 6.880724] T2T_Vmax 58, T2T_Vmin 82, 1'st_hole_Vmax 46, UI_Vmax 86
[ 6.890759] **Calculated values**
[ 6.897841] T2T_Vmax 57, 1'st_hole_Vmax 47, UI_Vmax 87
[ 6.906777] T2T_Vmin 57, 1'st_hole_Vmin 47, UI_Vmin 87
[ 6.915634] ***********************************
[ 6.923890] ***********final tuning windows**********
[ 6.932608] win[0]: 14 - 37
[ 6.939052] win[1]: 58 - 61
[ 6.945418] win[2]: 101 - 118
[ 6.951817] win[3]: 151 - 148
[ 6.958075] win[4]: 189 - 199
[ 6.964288] win[5]: 244 - 235
[ 6.970486] ********************************
[ 6.978008] best tap win - (14-37), best tap value 26 prev_best_tap 26
[ 6.987873] sdhci-tegra sdhci-tegra.3: sdhci_tegra_verify_best_tap: tuning freq 200000000hz, best tap 26
[ 7.003352] mmc0: new HS200 MMC card at address 0001
[ 7.011966] mmcblk mmc0:0001: Card claimed for testing.
[ 7.020885] mmcblk0: mmc0:0001 SEM16G 14.6 GiB
[ 7.029067] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB
[ 7.041215] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9
[ 7.716699] rt5639 0-001c: rt5639_headset_detect RT5639_PWR_ANLG1(0x63) = 0xa814
[ 7.728018] rt5639 0-001c: rt5639_headset_detect RT5639_IRQ_CTRL2(0xbe) = 0x0
[ 7.800942] rt5639 0-001c: rt5639_headset_detect jack_type = 2
[ 7.810839] tegra-snd-rt5639 tegra-snd-rt5639.0: rt5639-aif1 <-> tegra30-i2s.1 mapping ok
[ 7.823487] tegra-snd-rt5639 tegra-snd-rt5639.0: dit-hifi <-> tegra30-spdif mapping ok
[ 7.836039] tegra-snd-rt5639 tegra-snd-rt5639.0: dit-hifi <-> tegra30-i2s.3 mapping ok
[ 7.848497] tegra-snd-rt5639 tegra-snd-rt5639.0: rt5639-aif1 <-> dit-hifi mapping ok
[ 7.860809] tegra-snd-rt5639 tegra-snd-rt5639.0: dit-hifi <-> dit-hifi mapping ok
[ 7.872710] tegra-snd-rt5639 tegra-snd-rt5639.0: Allocating for stream playback
[ 7.883786] tegra-snd-rt5639 tegra-snd-rt5639.0: Allocating for stream capture
[ 7.894754] tegra-snd-rt5639 tegra-snd-rt5639.0: snd-soc-dummy-dai <-> tegra-offload-pcm mapping ok
[ 7.908198] compress asoc: snd-soc-dummy-dai <-> tegra-offload-compr mapping ok
[ 7.919899] tegra-snd-rt5639 tegra-snd-rt5639.0: Allocating for stream playback
[ 7.931108] tegra-snd-rt5639 tegra-snd-rt5639.0: Allocating for stream capture
[ 7.942228] tegra-snd-rt5639 tegra-snd-rt5639.0: snd-soc-dummy-dai <-> tegra-offload-pcm mapping ok
[ 7.955813] tegra-snd-rt5639 tegra-snd-rt5639.0: rt5639-aif1 <-> tegra30-i2s.1 mapping ok
[ 7.971748] input: tegra-rt5639 Headphone Jack as /devices/platform/tegra-snd-rt5639.0/sound/card1/input2
[ 7.986418] sysedp_create_consumer: unable to create speaker, no consumer_data for speaker found
[ 7.995941] oprofile: using timer interrupt.
[ 8.008673] GACT probability NOT on
[ 8.016274] Mirror/redirect action on
[ 8.024006] u32 classifier
[ 8.030760] Actions configured
[ 8.038165] Netfilter messages via NETLINK v0.30.
[ 8.046976] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 8.057574] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 8.068631] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 8.078872] xt_time: kernel timezone is -0000
[ 8.087631] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.097236] arp_tables: (C) 2002 David S. Miller
[ 8.106053] TCP: cubic registered
[ 8.113703] NET: Registered protocol family 10
[ 8.123089] mip6: Mobile IPv6
[ 8.130218] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 8.139929] sit: IPv6 over IPv4 tunneling driver
[ 8.149614] NET: Registered protocol family 17
[ 8.158278] NET: Registered protocol family 15
[ 8.166925] NET: Registered protocol family 35
[ 8.175520] NET: Registered protocol family 37
[ 8.184032] NET: Registered protocol family 41
[ 8.193830] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[ 8.229228] Registering SWP/SWPB emulation handler
[ 8.238194] last reset is due to power on reset
[ 8.238194]
[ 8.252550] Disabling clocks left on by bootloader:
[ 8.261590] audio_2x
[ 8.268191] audio
[ 8.274491] audio4
[ 8.280788] audio3
[ 8.287032] audio2
[ 8.293264] audio1
[ 8.299474] audio0
[ 8.305711] hdmi_audio
[ 8.312184] entropy
[ 8.318429] dsi2-fixed
[ 8.324928] dsi1-fixed
[ 8.331415] nor
[ 8.337272] trace
[ 8.343306] sdmmc4_ddr
[ 8.349778] sdmmc3_ddr
[ 8.356214] cclk_lp
[ 8.362233] pll_x_out0
[ 8.368420] pll_m_out1
[ 8.374712] tegra_dvfs: vdd_cpu connected to regulator
[ 8.383454] tegra_dvfs: vdd_core connected to regulator
[ 8.392269] tegra_dvfs: vdd_gpu connected to regulator
[ 8.402263] cpu_cold cooling device is registered
[ 8.410584] cpu_hot cooling device is registered
[ 8.410710] Tegra CPU DFLL is initialized with use_dfll = 1
[ 8.410772] CPU rate: 696 MHz
[ 8.601158] tegra dvfs: tegra sysfs cap interface is initialized
[ 8.610431] tegra dvfs: tegra sysfs gpu & emc interface is initialized
[ 8.620868] tegra_actmon.emc: Completed initialization (0)
[ 8.629852] tegra_actmon.avp: Completed initialization (0)
[ 8.638699] tegra_mon.cpu_emc: Completed initialization (0)
[ 8.650507] reg-aon-1v2: incomplete constraints, leaving on
[ 8.659419] reg-aon-1v8: incomplete constraints, leaving on
[ 8.668319] sdmmc-en-supply: incomplete constraints, leaving on
[ 8.677420] reg-dcdc-1v2: incomplete constraints, leaving on
[ 8.686349] reg-5v0-supply: incomplete constraints, leaving on
[ 8.695474] usb0-vbus: incomplete constraints, leaving on
[ 8.704146] vpp-fuse: incomplete constraints, leaving on
[ 8.712724] vdd-2v7-cam: incomplete constraints, leaving on
[ 8.721509] avdd-spi: incomplete constraints, leaving on
[ 8.730069] vdd-1v1-cam: incomplete constraints, leaving on
[ 8.738765] vddio-sdmmc-2: incomplete constraints, leaving on
[ 8.747643] vdd-1v2-cam: incomplete constraints, leaving on
[ 8.756380] avdd-cam: incomplete constraints, leaving on
[ 8.764872] vdd-cam: incomplete constraints, leaving on
[ 8.773298] as3722-sd3: incomplete constraints, leaving on
[ 8.781999] vdd-3v3-aon: incomplete constraints, leaving on
[ 8.790780] vdd-ac-bat: incomplete constraints, leaving on
[ 8.799450] regulator-dummy: incomplete constraints, leaving on
[ 8.809252] of_get_named_gpio_flags exited with status 128
[ 8.809305] gpio wake51 for gpio=128
[ 8.816280] input: gpio-keys.3 as /devices/platform/gpio-keys.3/input/input3
[ 8.827313] as3722-rtc as3722-rtc.1: setting system clock to 2000-01-01 00:46:50 UTC (946687610)
[ 8.840253] ALSA device list:
[ 8.845906] #0: HDA NVIDIA Tegra at 0x70038000 irq 113
[ 8.853935] #1: tegra-rt5639
[ 8.860710] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities
[ 8.872158] EXT4-fs (mmcblk0p1): couldn't mount as ext2 due to feature incompatibilities
[ 9.336115] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281197
[ 9.336329] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281199
[ 9.336450] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281200
[ 9.336532] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281191
[ 9.336608] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281109
[ 9.336713] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281142
[ 9.336791] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281140
[ 9.336865] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 280984
[ 9.336942] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281132
[ 9.337023] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281190
[ 9.337097] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281181
[ 9.337177] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 573031
[ 9.337254] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 573030
[ 9.337329] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281146
[ 9.337402] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 573029
[ 9.337479] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 573028
[ 9.337552] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281141
[ 9.337625] EXT4-fs (mmcblk0p1): ext4_orphan_cleanup: deleting unreferenced inode 281188
[ 9.337744] EXT4-fs (mmcblk0p1): 18 orphan inodes deleted
[ 9.346110] EXT4-fs (mmcblk0p1): recovery complete
[ 9.367572] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[ 9.378728] VFS: Mounted root (ext4 filesystem) on device 179:1.
[ 9.397199] devtmpfs: mounted
[ 9.403548] Freeing unused kernel memory: 496K (c0b5c000 - c0bd8000)
[ 9.649747] init: plymouth-upstart-bridge main process (119) terminated with status 1
[ 9.661936] init: plymouth-upstart-bridge main process ended, respawning
[ 9.713826] init: plymouth-upstart-bridge main process (129) terminated with status 1
[ 9.725619] init: plymouth-upstart-bridge main process ended, respawning
[ 9.740707] init: ureadahead main process (122) terminated with status 5
[ 9.781501] init: plymouth-upstart-bridge main process (134) terminated with status 1
[ 9.793429] init: plymouth-upstart-bridge main process ended, respawning
[ 11.275236] systemd-udevd[304]: starting version 204
[ 11.641636] Tegra cpuquiet clusterswitch enabled
[ 11.698472] otg state changed: PERIPHERAL --> SUSPEND
[ 11.698716] tegra-udc tegra-udc.0: USB cable/charger disconnected
[ 11.699020] otg state changed: SUSPEND --> HOST
[ 11.700314] tegra USB phy - inst[0] platform info:
[ 11.700340] port_otg: yes
[ 11.700353] has_hostpc: yes
[ 11.700367] phy_interface: USB_PHY_INTF_UTMI
[ 11.700379] op_mode: TEGRA_USB_OPMODE_HOST
[ 11.700396] qc2_voltage: 0
[ 11.700413] vbus_gpio: -1
[ 11.700428] hot_plug: disabled
[ 11.700446] remote_wakeup: enabled
[ 11.758193] vi vi.0: vi_probe: ++
[ 11.777228] vi vi.0: initialized
[ 11.778060] vi vi.1: vi_probe: ++
[ 11.780716] vi vi.1: initialized
[ 12.026649] Bluetooth: Core ver 2.16
[ 12.032470] NET: Registered protocol family 31
[ 12.032493] Bluetooth: HCI device and connection manager initialized
[ 12.032561] Bluetooth: HCI socket layer initialized
[ 12.032595] Bluetooth: L2CAP socket layer initialized
[ 12.032719] Bluetooth: SCO socket layer initialized
[ 12.081222] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 12.081298] Bluetooth: BNEP socket layer initialized
[ 12.232942] Bluetooth: RFCOMM socket layer initialized
[ 12.232951] Bluetooth: RFCOMM ver 1.11
[ 12.703178] tegra-ehci tegra-ehci.0: Tegra EHCI Host Controller
[ 12.703250] tegra-ehci tegra-ehci.0: new USB bus registered, assigned bus number 3
[ 12.703542] tegra-ehci tegra-ehci.0: irq 52, io mem 0x7d000000
[ 12.708741] tegra-ehci tegra-ehci.0: USB 2.0 started, EHCI 1.10
[ 12.708975] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 12.708987] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 12.708999] usb usb3: Product: Tegra EHCI Host Controller
[ 12.709009] usb usb3: Manufacturer: Linux 3.10.40-gb271e8f ehci_hcd
[ 12.709020] usb usb3: SerialNumber: tegra-ehci.0
[ 12.710229] hub 3-0:1.0: USB hub found
[ 12.710275] hub 3-0:1.0: 1 port detected
[ 12.943767] init: udev-fallback-graphics main process (445) terminated with status 1
[ 12.973826] device-mapper: uevent: version 1.0.3
[ 12.974239] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 13.755780] r8169 0000:01:00.0 eth0: link down
[ 13.755958] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.233279] init: plymouth-upstart-bridge main process ended, respawning
[ 14.453542] init: plymouth-stop pre-start process (935) terminated with status 1
[ 15.054766] tegradc tegradc.1: nominal-pclk:148500000 parent:594000000 div:4.0 pclk:148500000 147015000~161865000
[ 15.054871] tegra_dc_hdmi_enable: HDMI clock already configured to target frequency, skipping clk setup.
[ 15.357815] init: Failed to obtain startpar-bridge instance: Unknown parameter: INSTANCE
[ 16.105153] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
[ 16.118770] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
[ 17.388279] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
[ 17.403913] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
[ 18.385455] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
[ 18.410181] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
[ 18.454199] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
[ 66.058985] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
[ 135.325635] init: plymouth-stop pre-start process (2049) terminated with status 1
[ 180.336348] r8169 0000:01:00.0 eth0: link up
[ 180.337125] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 199.266973] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
[ 5045.728836] tegra_dc_hdmi_irq: start
[ 5045.729218] tegra_dc_hdmi_irq: end
[ 5045.729985] hdmi_state_machine_worker (tid e9f40040): state 4 (Enabled), hpd 0, pending_hpd_evt 1
[ 5045.730146] hdmi_state_machine_set_state_l: switching from state 4 (Enabled) to state 5 (Wait for HPD reassert)
[ 5047.233457] hdmi_state_machine_worker (tid e9f40040): state 5 (Wait for HPD reassert), hpd 0, pending_hpd_evt 0
[ 5047.234078] hdmi_state_machine_set_state_l: switching from state 5 (Wait for HPD reassert) to state 0 (Reset)
[ 5047.234320] hdmi_state_machine_worker (tid e9f40040): state 0 (Reset), hpd 0, pending_hpd_evt 0
[ 5047.247342] hdmi_disable_l: audio_switch 0
[ 5047.248308] hdmi_disable_l: hpd_switch 0
[ 5047.256415] HDMI from connected to disconnected
[ 5047.266210] hdmi_state_machine_set_state_l: switching from state 0 (Reset) to state 1 (Check Plug)
[ 5047.279620] hdmi_state_machine_worker (tid e9f40040): state 1 (Check Plug), hpd 0, pending_hpd_evt 0
[ 5047.279648] hdmi_disable_l: audio_switch 0
[ 5047.279654] hdmi_disable_l: hpd_switch 0
[ 5047.279664] hdmi_state_machine_set_state_l: switching from state 1 (Check Plug) to state 3 (Disabled)
[ 5047.323993] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
[ 5047.627150] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
[ 5051.719851] tegra_dc_hdmi_irq: start
[ 5051.720510] tegra_dc_hdmi_irq: end
[ 5051.721995] hdmi_state_machine_worker (tid e9f40040): state 3 (Disabled), hpd 1, pending_hpd_evt 1
[ 5051.722161] hdmi_state_machine_set_state_l: switching from state 3 (Disabled) to state 0 (Reset)
[ 5051.763441] hdmi_state_machine_worker (tid e9f40040): state 0 (Reset), hpd 1, pending_hpd_evt 0
[ 5051.770976] hdmi_disable_l: audio_switch 0
[ 5051.771128] hdmi_disable_l: hpd_switch 0
[ 5051.771291] hdmi_state_machine_set_state_l: switching from state 0 (Reset) to state 1 (Check Plug)
[ 5051.783327] hdmi_state_machine_worker (tid e9f40040): state 1 (Check Plug), hpd 1, pending_hpd_evt 0
[ 5051.783429] hdmi_state_machine_set_state_l: switching from state 1 (Check Plug) to state 2 (Check EDID)
[ 5051.843465] hdmi_state_machine_worker (tid e9f40040): state 2 (Check EDID), hpd 1, pending_hpd_evt 0
[ 5051.873818] Reserved SVD code 97
[ 5051.873899] Reserved SVD code 96
[ 5051.873952] Reserved SVD code 102
[ 5051.874000] Reserved SVD code 101
[ 5051.874048] Reserved SVD code 95
[ 5051.874093] Reserved SVD code 100
[ 5051.874138] Reserved SVD code 93
[ 5051.874183] Reserved SVD code 98
[ 5051.874229] Reserved SVD code 94
[ 5051.874275] Reserved SVD code 99
[ 5051.874482] panel size 0 by 0
[ 5051.896236] handle_check_edid_l: audio_switch 1
[ 5051.900658] Display connected, hpd_switch 1
[ 5051.912139] hdmi_state_machine_set_state_l: switching from state 2 (Check EDID) to state 4 (Enabled)
[ 5051.912260] hdmi_state_machine_worker (tid e9f40040): state 4 (Enabled), hpd 1, pending_hpd_evt 0
[ 5051.915167] tegradc tegradc.1: nominal-pclk:148500000 parent:594000000 div:4.0 pclk:148500000 147015000~161865000
[ 5051.920887] tegra_dc_hdmi_enable: HDMI clock already configured to target frequency, skipping clk setup.
[ 5051.992191] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
[ 5052.133642] tegradc tegradc.1: nominal-pclk:148500000 parent:594000000 div:4.0 pclk:148500000 147015000~161865000
[ 5052.133745] tegra_dc_hdmi_enable: HDMI clock already configured to target frequency, skipping clk setup.
[ 5052.246912] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
[ 5052.310682] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
[ 5052.350776] gk20a gk20a.0: unrecognized ioctl cmd: 0x8008486d
ubuntu@tegra-ubuntu:~$

#3
Posted 02/12/2018 01:04 PM   
Hi merwin, Are you using rel-21.5 or rel-21.6?
Hi merwin,

Are you using rel-21.5 or rel-21.6?

#4
Posted 02/13/2018 03:15 AM   
Could you help do below test on your tk1? 1. Check polarity when gnome desktop GUI is on. 2. Check it again after change to console mode (through ctrl+alt +f1~f6)
Could you help do below test on your tk1?

1. Check polarity when gnome desktop GUI is on.
2. Check it again after change to console mode (through ctrl+alt +f1~f6)

#5
Posted 02/13/2018 05:09 AM   
I'm using rel-21.6. Polarity is wrong with gnome desktop GUI. Still wrong with console mode.
I'm using rel-21.6.

Polarity is wrong with gnome desktop GUI.

Still wrong with console mode.

#6
Posted 02/13/2018 12:40 PM   
Please try to replace this file under your system.
Please try to replace this file under your system.
Attachments

libnvdc.so.tar.gz

#7
Posted 02/14/2018 02:23 AM   
With the attached libnvdc.so the sync polarities are now always positive which is still wrong but at least matches the xrandr values.
With the attached libnvdc.so the sync polarities are now always positive which is still wrong but at least matches the xrandr values.

#8
Posted 02/14/2018 07:55 PM   
Hi merwin, I don't get it. This polarity should always match the xrandr values which are from edid. Is there still anything wrong??
Hi merwin,

I don't get it. This polarity should always match the xrandr values which are from edid. Is there still anything wrong??

#9
Posted 02/15/2018 02:53 AM   
The sync polarities are lost when xrandr gets the modes from the kernel. They are correct in the kernel (from the edid).
The sync polarities are lost when xrandr gets the modes from the kernel. They are correct in the kernel (from the edid).

#10
Posted 02/15/2018 01:50 PM   
Scroll To Top

Add Reply