My Jetson Nano dev board used to work just fine, Ubuntu worked fine and I was able to use USB devices normally, running off the 5V barrel jack. I installed an Intel 8265NGW wifi card, tried booting it and subsequently none of the USB ports worked for any devices (not even KB / mouse). I can still see the boot messages but cannot do anything.
Anyone have any similar issues? I’m hoping the board won’t be a total write-off, can’t use it without working USB ports!
Hi,
Are you able to boot up device? Could you dump the dmesg?
Yes, the device boots up to an Ubuntu setup screen (GUI) when I use a fresh image. But cannot click on or type anything since the USB ports are not functioning. Can you give me any hint on how I would be able to dump the dmesg without use of the keyboard or mouse?
I managed to mount the sdcard on a Mac and get the Xlog, but couldn’t find where the dmesg log file was:
[ 14.826]
X.Org X Server 1.19.6
Release Date: 2017-12-20
[ 14.826] X Protocol Version 11, Revision 0
[ 14.826] Build Operating System: Linux 4.4.0-138-generic aarch64 Ubuntu
[ 14.826] Current Operating System: Linux tegra-ubuntu 4.9.140-tegra #1 SMP PREEMPT Wed Mar 13 00:32:22 PDT 2019 aarch64
[ 14.826] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 tegra_fbmem=0x140000@0x92cb6000 is_hdmi_initialised=1 root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 rootfstype=ext4 root=/dev/mmcblk0p1 rw rootwait
[ 14.826] Build Date: 25 October 2018 04:10:37PM
[ 14.826] xorg-server 2:1.19.6-1ubuntu4.2 (For technical support please see http://www.ubuntu.com/support)
[ 14.826] Current version of pixman: 0.34.0
[ 14.826] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 14.826] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 14.827] (==) Log file: "/var/log/Xorg.0.log", Time: Sun Jan 28 15:58:26 2018
[ 14.828] (==) Using config file: "/etc/X11/xorg.conf"
[ 14.828] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 14.831] (==) No Layout section. Using the first Screen section.
[ 14.831] (==) No screen section available. Using defaults.
[ 14.831] (**) |-->Screen "Default Screen Section" (0)
[ 14.831] (**) | |-->Monitor "<default monitor>"
[ 14.831] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 14.831] (**) | |-->Device "Tegra0"
[ 14.831] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 14.832] (==) Automatically adding devices
[ 14.832] (==) Automatically enabling devices
[ 14.832] (==) Automatically adding GPU devices
[ 14.832] (==) Automatically binding GPU devices
[ 14.832] (==) Max clients allowed: 256, resource mask: 0x1fffff
[ 14.839] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[ 14.839] Entry deleted from font path.
[ 14.839] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
[ 14.839] Entry deleted from font path.
[ 14.839] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
[ 14.839] Entry deleted from font path.
[ 14.839] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
[ 14.839] Entry deleted from font path.
[ 14.839] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
[ 14.839] Entry deleted from font path.
[ 14.839] (==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/Type1,
built-ins
[ 14.839] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 14.839] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 14.839] (II) Loader magic: 0x556c567010
[ 14.839] (II) Module ABI versions:
[ 14.839] X.Org ANSI C Emulation: 0.4
[ 14.839] X.Org Video Driver: 23.0
[ 14.839] X.Org XInput driver : 24.1
[ 14.839] X.Org Server Extension : 10.0
[ 14.840] (++) using VT number 7
[ 14.840] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[ 14.842] (II) no primary bus or device found
[ 14.842] (WW) "dri" will not be loaded unless you've specified it to be loaded elsewhere.
[ 14.842] (II) "glx" will be loaded by default.
[ 14.842] (II) LoadModule: "extmod"
[ 14.842] (II) Module "extmod" already built-in
[ 14.842] (II) LoadModule: "glx"
[ 14.844] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 14.889] (II) Module glx: vendor="X.Org Foundation"
[ 14.889] compiled for 1.19.6, module version = 1.0.0
[ 14.889] ABI class: X.Org Server Extension, version 10.0
[ 14.889] (II) LoadModule: "nvidia"
[ 14.890] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 14.934] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 14.934] compiled for 4.0.2, module version = 1.0.0
[ 14.934] Module class: X.Org Video Driver
[ 14.942] (II) NVIDIA dlloader X Driver 32.1.0 Release Build (integ_stage_rel) (buildbrain@mobile-u64-3531) Wed Mar 13 00:27:48 PDT 2019
[ 14.942] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 14.948] (WW) Falling back to old probe method for NVIDIA
[ 14.948] (II) Loading sub module "fb"
[ 14.948] (II) LoadModule: "fb"
[ 14.949] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 14.951] (II) Module fb: vendor="X.Org Foundation"
[ 14.951] compiled for 1.19.6, module version = 1.0.0
[ 14.951] ABI class: X.Org ANSI C Emulation, version 0.4
[ 14.951] (II) Loading sub module "wfb"
[ 14.951] (II) LoadModule: "wfb"
[ 14.952] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 14.954] (II) Module wfb: vendor="X.Org Foundation"
[ 14.954] compiled for 1.19.6, module version = 1.0.0
[ 14.954] ABI class: X.Org ANSI C Emulation, version 0.4
[ 14.955] (II) Loading sub module "ramdac"
[ 14.955] (II) LoadModule: "ramdac"
[ 14.955] (II) Module "ramdac" already built-in
[ 14.956] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
[ 14.956] (II) NVIDIA(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 14.956] (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
[ 14.956] (==) NVIDIA(0): RGB weight 888
[ 14.956] (==) NVIDIA(0): Default visual is TrueColor
[ 14.956] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 14.956] (DB) xf86MergeOutputClassOptions unsupported bus type 0
[ 14.956] (**) NVIDIA(0): Option "AllowEmptyInitialConfiguration" "true"
[ 14.956] (**) NVIDIA(0): Enabling 2D acceleration
[ 14.956] (II) Loading sub module "glxserver_nvidia"
[ 14.956] (II) LoadModule: "glxserver_nvidia"
[ 14.957] (II) Loading /usr/lib/xorg/modules/extensions/libglxserver_nvidia.so
[ 15.201] (II) Module glxserver_nvidia: vendor="NVIDIA Corporation"
[ 15.201] compiled for 4.0.2, module version = 1.0.0
[ 15.201] Module class: X.Org Server Extension
[ 15.201] (II) NVIDIA GLX Module 32.1.0 Release Build (integ_stage_rel) (buildbrain@mobile-u64-3531) Wed Mar 13 00:26:03 PDT 2019
[ 15.267] (--) NVIDIA(0): Valid display device(s) on GPU-0 at SoC
[ 15.267] (--) NVIDIA(0): DFP-0
[ 15.267] (--) NVIDIA(0): DFP-1
[ 15.267] (II) NVIDIA(0): NVIDIA GPU NVIDIA Tegra X1 (nvgpu) (GM20B) at SoC (GPU-0)
[ 15.267] (--) NVIDIA(0): Memory: 4058432 kBytes
[ 15.267] (--) NVIDIA(0): VideoBIOS:
[ 15.268] (--) NVIDIA(GPU-0): DELL 1908FP (DFP-0): connected
[ 15.268] (--) NVIDIA(GPU-0): DELL 1908FP (DFP-0): External TMDS
[ 15.268] (==) NVIDIA(0):
[ 15.268] (==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
[ 15.268] (==) NVIDIA(0): will be used as the requested mode.
[ 15.268] (==) NVIDIA(0):
[ 15.268] (II) NVIDIA(0): Validated MetaModes:
[ 15.268] (II) NVIDIA(0): "DFP-0:nvidia-auto-select"
[ 15.268] (II) NVIDIA(0): Virtual screen size determined to be 1280 x 1024
[ 15.269] (--) NVIDIA(0): DPI set to (85, 86); computed from "UseEdidDpi" X config
[ 15.269] (--) NVIDIA(0): option
[ 15.269] (--) Depth 24 pixmap format is 32 bpp
[ 15.269] (II) NVIDIA: Reserving 6144.00 MB of virtual memory for indirect memory
[ 15.269] (II) NVIDIA: access.
[ 15.271] (EE) NVIDIA(0): Failed to allocate NVIDIA Error Handler
[ 15.271] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[ 15.271] (II) NVIDIA(0): may not be running or the "AcpidSocketPath" X
[ 15.271] (II) NVIDIA(0): configuration option may not be set correctly. When the
[ 15.271] (II) NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
[ 15.271] (II) NVIDIA(0): try to use it to receive ACPI event notifications. For
[ 15.271] (II) NVIDIA(0): details, please see the "ConnectToAcpid" and
[ 15.271] (II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
[ 15.271] (II) NVIDIA(0): Config Options in the README.
[ 15.327] (II) NVIDIA(0): Setting mode "DFP-0:nvidia-auto-select"
[ 15.424] (==) NVIDIA(0): Disabling shared memory pixmaps
[ 15.424] (==) NVIDIA(0): Backing store enabled
[ 15.424] (==) NVIDIA(0): Silken mouse enabled
[ 15.431] (==) NVIDIA(0): DPMS enabled
[ 15.431] (II) Loading sub module "dri2"
[ 15.431] (II) LoadModule: "dri2"
[ 15.431] (II) Module "dri2" already built-in
[ 15.431] (II) NVIDIA(0): [DRI2] Setup complete
[ 15.431] (II) NVIDIA(0): [DRI2] VDPAU driver: nvidia
[ 15.450] (--) RandR disabled
[ 15.458] (II) SELinux: Disabled on system
[ 15.459] (II) Initializing extension GLX
[ 15.459] (II) Indirect GLX disabled.
[ 15.621] (II) config/udev: Adding input device tegra-hda HDMI/DP,pcm=3 (/dev/input/event0)
[ 15.621] (II) No input driver specified, ignoring this device.
[ 15.621] (II) This device may have been added with another device file.
[ 15.622] (II) config/udev: Adding input device gpio-keys (/dev/input/event1)
[ 15.622] (**) gpio-keys: Applying InputClass "libinput keyboard catchall"
[ 15.622] (II) LoadModule: "libinput"
[ 15.626] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[ 15.637] (II) Module libinput: vendor="X.Org Foundation"
[ 15.637] compiled for 1.19.6, module version = 0.27.1
[ 15.637] Module class: X.Org XInput Driver
[ 15.637] ABI class: X.Org XInput driver, version 24.1
[ 15.637] (II) Using input driver 'libinput' for 'gpio-keys'
[ 15.637] (**) gpio-keys: always reports core events
[ 15.637] (**) Option "Device" "/dev/input/event1"
[ 15.637] (**) Option "_source" "server/udev"
[ 15.638] (II) event1 - gpio-keys: is tagged by udev as: Keyboard
[ 15.638] (II) event1 - gpio-keys: device is a keyboard
[ 15.638] (II) event1 - gpio-keys: device removed
[ 15.680] (**) Option "config_info" "udev:/sys/devices/gpio-keys/input/input1/event1"
[ 15.680] (II) XINPUT: Adding extended input device "gpio-keys" (type: KEYBOARD, id 6)
[ 15.680] (**) Option "xkb_model" "pc105"
[ 15.680] (**) Option "xkb_layout" "us"
[ 15.681] (II) event1 - gpio-keys: is tagged by udev as: Keyboard
[ 15.681] (II) event1 - gpio-keys: device is a keyboard
[ 16.989] (--) NVIDIA(GPU-0): DELL 1908FP (DFP-0): connected
[ 16.989] (--) NVIDIA(GPU-0): DELL 1908FP (DFP-0): External TMDS
[ 17.098] (II) NVIDIA(0): Setting mode "HDMI-0: nvidia-auto-select @1280x1024 +0+0 {ViewPortIn=1280x1024, ViewPortOut=1280x1024+0+0}"
[ 17.998] (--) NVIDIA(GPU-0): DELL 1908FP (DFP-0): connected
[ 17.998] (--) NVIDIA(GPU-0): DELL 1908FP (DFP-0): External TMDS
[ 18.029] (--) NVIDIA(GPU-0): DELL 1908FP (DFP-0): connected
[ 18.029] (--) NVIDIA(GPU-0): DELL 1908FP (DFP-0): External TMDS
UART or ssh should still work.
I have managed to capture these boot messages from UART, do you see any issues in here?
[code]
22:07:38.609 → [0000.126] [TegraBoot] (version 00.00.2018.01-l4t-33e7fa82)
22:07:38.885 → [0000.131] Processing in cold boot mode Bootloader 2
22:07:38.885 → [0000.136] A02 Bootrom Patch rev = 1023
22:07:38.885 → [0000.139] Power-up reason: pmc por
22:07:38.885 → [0000.142] No Battery Present
22:07:38.885 → [0000.145] pmic max77620 reset reason
22:07:38.885 → [0000.148] pmic max77620 NVERC : 0x40
22:07:38.885 → [0000.152] RamCode = 0
22:07:38.885 → [0000.154] Platform has DDR4 type RAM
22:07:38.885 → [0000.157] max77620 disabling SD1 Remote Sense
22:07:38.885 → [0000.161] Setting DDR voltage to 1125mv
22:07:38.885 → [0000.165] Serial Number of Pmic Max77663: 0x1d24e6
22:07:38.885 → [0000.173] Entering ramdump check
22:07:38.885 → [0000.176] Get RamDumpCarveOut = 0x0
22:07:38.885 → [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
22:07:38.885 → [0000.184] Last reboot was clean, booting normally!
22:07:38.885 → [0000.189] Sdram initialization is successful
22:07:38.885 → [0000.193] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
22:07:38.885 → [0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
22:07:38.885 → [0000.205] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
22:07:38.885 → [0000.211] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
22:07:38.885 → [0000.217] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
22:07:38.885 → [0000.223] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
22:07:38.885 → [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
22:07:38.885 → [0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
22:07:38.885 → [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
22:07:38.928 → [0000.257] Platform-DebugCarveout: 0
22:07:38.928 → [0000.260] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
22:07:38.928 → [0000.266] Non secure mode, and RB not enabled.
22:07:38.928 → [0000.272] Invalid GPT Partition
22:07:38.928 → [0000.287] Using BFS PT to query partitions
22:07:38.928 → [0000.291] failed to load NvTbootTbootCpu from (2:0)
22:07:38.928 → [0000.296] re-load NvTbootTbootCpu from (4:0)
22:07:39.094 → [0000.446] Csd NumOfBlocks=249737216
22:07:39.128 → [0000.506] Using GPT Primary to query partitions
22:07:39.161 → [0000.516] Loading Tboot-CPU binary
22:07:39.577 → [0000.893] Verifying TBC in OdmNonSecureSBK mode
22:07:39.577 → [0000.903] Bootloader load address is 0xa0000000, entry address is 0xa0000258
22:07:39.577 → [0000.910] Bootloader downloaded successfully.
22:07:39.577 → [0000.914] Downloaded Tboot-CPU binary to 0xa0000258
22:07:39.577 → [0000.919] MAX77620_GPIO5 configured
22:07:39.577 → [0000.923] CPU power rail is up
22:07:39.577 → [0000.926] CPU clock enabled
22:07:39.577 → [0000.929] Performing RAM repair
22:07:39.577 → [0000.932] Updating A64 Warmreset Address to 0xa00002e9
22:07:39.577 → [0000.937] Loading NvTbootBootloaderDTB
22:07:40.925 → [0002.248] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
22:07:40.991 → [0002.310] Bootloader DTB Load Address: 0x83000000
22:07:40.991 → [0002.314] Loading NvTbootKernelDTB
22:07:42.361 → [0003.625] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
22:07:42.395 → [0003.686] Kernel DTB Load Address: 0x83100000
22:07:42.395 → [0003.696] Loading cboot binary
22:07:44.134 → [0005.377] Verifying EBT in OdmNonSecureSBK mode
22:07:44.203 → [0005.420] Bootloader load address is 0x92c00000, entry address is 0x92c00258
22:07:44.203 → [0005.427] Bootloader downloaded successfully.
22:07:44.417 → [0005.621] Using BFS PT to query partitions
22:07:44.417 → [0005.625] Next binary entry address: 0x92c00258
22:07:44.417 → [0005.629] BoardId: 3448
22:07:44.417 → [0005.634] Overriding pmu board id with proc board id
22:07:44.417 → [0005.639] Display board id is not available
22:07:45.953 → [0007.137] Verifying SC7EntryFw in OdmNonSecureSBK mode
22:07:45.988 → [0007.190] /bpmp deleted
22:07:45.988 → [0007.192] SC7EntryFw header found loaded at 0xff700000
22:07:46.197 → [0007.383] OVR2 PMIC
22:07:46.197 → [0007.385] Bpmp FW successfully loaded
22:07:46.197 → [0007.403] WB0 init successfully at 0xff780000
22:07:46.230 → [0007.408] Set NvDecSticky Bits
22:07:46.230 → [0007.411] GSC2 address ff53fffc value c0edbbcc
22:07:46.230 → [0007.417] GSC MC Settings done
22:07:46.230 → [0007.425] TOS Image length 53680
22:07:46.230 → [0007.428] Monitor size 53680
22:07:46.230 → [0007.431] OS size 0
22:07:46.406 → [0007.594] Secure Os AES-CMAC Verification Success!
22:07:46.406 → [0007.598] TOS image cipher info: plaintext
22:07:46.406 → [0007.602] Loading and Validation of Secure OS Successful
22:07:46.406 → [0007.618] SC7 Entry Firmware - 0xff700000, 0x4000
22:07:46.507 → [0007.623] NvTbootPackSdramParams: start.
22:07:46.507 → [0007.628] NvTbootPackSdramParams: done.
22:07:46.507 → [0007.632] Tegraboot started after 53289 us
22:07:46.507 → [0007.635] Basic modules init took 5725528 us
22:07:46.507 → [0007.640] NvTbootQspiFlashIoctl: Opcode = 1 not supported
22:07:46.507 → [0007.645] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB
22:07:46.507 → [0007.650] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
22:07:46.507 → [0007.656] Storage Device Read Time = 6749 ms, Read Size = 2306 KB
22:07:46.507 → [0007.662] Storage Device Write Time = 0 ms, Write Size = 0 KB
22:07:46.507 → [0007.667] Next stage binary read took 1529678 us
22:07:46.507 → [0007.672] Carveout took -1541359 us
22:07:46.507 → [0007.675] CPU initialization took 2047984 us
22:07:46.507 → [0007.679] Total time taken by TegraBoot 7761831 us
22:07:46.507 →
22:07:46.507 → [0007.684] Starting CPU & Halting co-processor
22:07:46.507 →
22:07:46.507 → 64NOTICE: BL31: v1.3(release):eca0c5e
22:07:46.507 → NOTICE: BL31: Built : 00:21:27, Mar 13 2019
22:07:46.507 → ERROR: Error initializing runtime service trusty_fast
22:07:46.611 → [0007.806] RamCode = 0
22:07:46.863 → [0007.811] LPDDR4 Training: Read DT: Number of tables = 2
22:07:46.863 → [0007.816] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
22:07:46.863 → [0007.828] EMC Training Successful
22:07:46.863 → [0007.831] 408000 not found in DVFS table
22:07:46.863 → [0007.838] RamCode = 0
22:07:46.863 → [0007.841] DT Write: emc-table@204000 succeeded
22:07:46.863 → [0007.847] DT Write: emc-table@1600000 succeeded
22:07:46.863 → [0007.851] LPDDR4 Training: Write DT: Number of tables = 2
22:07:46.863 → [0008.048]
22:07:46.863 → [0008.049] Debug Init done
22:07:46.863 → [0008.052] Marked DTB cacheable
22:07:46.863 → [0008.055] Bootloader DTB loaded at 0x83000000
22:07:46.863 → [0008.060] Marked DTB cacheable
22:07:46.863 → [0008.063] Kernel DTB loaded at 0x83100000
22:07:46.863 → [0008.067] DeviceTree Init done
22:07:46.863 → [0008.079] Pinmux applied successfully
22:07:46.863 → [0008.083] gicd_base: 0x50041000
22:07:46.863 → [0008.087] gicc_base: 0x50042000
22:07:46.863 → [0008.090] Interrupts Init done
22:07:46.863 → [0008.094] Using base:0x60005090 & irq:208 for tick-timer
22:07:46.863 → [0008.099] Using base:0x60005098 for delay-timer
22:07:46.863 → [0008.103] platform_init_timer: DONE
22:07:46.863 → [0008.107] Timer(tick) Init done
22:07:46.863 → [0008.111] osc freq = 38400 khz
22:07:46.863 → [0008.115]
22:07:46.863 → [0008.116] welcome to cboot
22:07:46.863 → [0008.118]
22:07:46.863 → [0008.119] Cboot Version: 00.00.2018.01-t210-f76b856b
22:07:46.863 → [0008.124] calling constructors
22:07:46.863 → [0008.127] initializing heap
22:07:46.863 → [0008.130] initializing threads
22:07:46.863 → [0008.133] initializing timers
22:07:46.863 → [0008.136] creating bootstrap completion thread
22:07:46.863 → [0008.140] top of bootstrap2()
22:07:46.863 → [0008.143] CPU: ARM Cortex A57
22:07:46.863 → [0008.146] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
22:07:46.863 → [0008.151] initializing platform
22:07:46.863 → [0008.154] Scratch reg 37 & 271 initial value set…
22:07:46.863 → [0008.160] cboot:secure-pmc present
22:07:46.863 → [0008.163] Manufacturer: MF = 0xc2, ID MSB = 0x25
22:07:46.863 → [0008.168] ID LSB = 0x36, ID-CFI len = 194 bytes
22:07:46.863 → [0008.172] Macronix QSPI chip present
22:07:46.863 → [0008.176] SPI device register
22:07:46.863 → [0008.179] init boot device
22:07:46.863 → [0008.181] allocating memory for boot device(SPI)
22:07:46.863 → [0008.186] registering boot device
22:07:46.863 → [0008.195] sdmmc node status = okay
22:07:46.863 → [0008.199] sdcard instance = 0
22:07:46.863 → [0008.201] sdcard gpio handle 0x5d
22:07:46.863 → [0008.205] sdcard gpio pin 0xc9
22:07:46.863 → [0008.208] sdcard gpio flags 0x0
22:07:46.863 → [0008.211] vmmc-supply 0x9d
22:07:46.863 → [0008.213] Instance: 0
22:07:46.863 → [0008.215] Allocating memory for context
22:07:46.863 → [0008.219] enabling clock
22:07:46.863 → [0008.222] sd card init
22:07:46.863 → [0008.224] Check card present and stable
22:07:46.863 → [0008.228] Send command 0
22:07:46.915 → [0008.252] Send command 3
22:07:46.915 → [0008.256] Set RCA for the card
22:07:46.915 → [0008.259] Query card specific data by command 9
22:07:46.915 → [0008.266] Parse CSD data
22:07:46.915 → [0008.268] Send command 7
22:07:46.915 → [0008.279] Calling sd device register
22:07:46.915 → [0008.282] Init sdcard
22:07:46.915 → [0008.284] Allocating memory for boot device
22:07:46.915 → [0008.288] Registering user device
22:07:47.075 → [0008.301] Enable APE clock
22:07:47.075 → [0008.304] Un-powergate APE partition
22:07:47.075 → [0008.307] of_register: registering tegra_udc to of_hal
22:07:47.075 → [0008.313] of_register: registering tegra_udc to of_hal
22:07:47.075 → [0008.318] of_register: registering inv20628-driver to of_hal
22:07:47.075 → [0008.323] of_register: registering ads1015-driver to of_hal
22:07:47.075 → [0008.329] of_register: registering lp8557-bl-driver to of_hal
22:07:47.075 → [0008.335] of_register: registering bq2419x_charger to of_hal
22:07:47.075 → [0008.340] of_register: registering cpc to of_hal
22:07:47.075 → [0008.345] of_register: registering bq27441_fuel_gauge to of_hal
22:07:47.075 → [0008.356] gpio framework initialized
22:07:47.075 → [0008.360] of_register: registering tca9539_gpio to of_hal
22:07:47.075 → [0008.365] of_register: registering tca9539_gpio to of_hal
22:07:47.075 → [0008.370] of_register: registering i2c_bus_driver to of_hal
22:07:47.075 → [0008.376] of_register: registering i2c_bus_driver to of_hal
22:07:47.075 → [0008.382] of_register: registering i2c_bus_driver to of_hal
22:07:47.075 → [0008.387] of_register: registering i2c_bus_driver to of_hal
22:07:47.075 → [0008.393] pmic framework initialized
22:07:47.075 → [0008.396] of_register: registering max77620_pmic to of_hal
22:07:47.075 → [0008.402] regulator framework initialized
22:07:47.075 → [0008.406] of_register: registering tps65132_bl_driver to of_hal
22:07:47.075 → [0008.411] initializing target
22:07:47.075 → [0008.417] gpio_driver_register: register ‘tegra_gpio_driver’ driver
22:07:47.075 → [0008.426] fixed regulator driver initialized
22:07:47.075 → [0008.444] initializing OF layer
22:07:47.252 → [0008.446] NCK carveout not present
22:07:47.252 → [0008.450] Skipping dts_overrides
22:07:47.252 → [0008.454] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
22:07:47.252 → [0008.470] I2C Bus Init done
22:07:47.252 → [0008.472] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
22:07:47.252 → [0008.483] I2C Bus Init done
22:07:47.252 → [0008.485] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
22:07:47.252 → [0008.495] I2C Bus Init done
22:07:47.252 → [0008.498] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
22:07:47.252 → [0008.508] I2C Bus Init done
22:07:47.252 → [0008.511] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
22:07:47.252 → [0008.521] I2C Bus Init done
22:07:47.252 → [0008.524] of_children_init: Ops found for compatible string maxim,max77620
22:07:47.252 → [0008.534] max77620_init using irq 118
22:07:47.252 → [0008.539] register ‘maxim,max77620’ pmic
22:07:47.252 → [0008.543] gpio_driver_register: register ‘max77620-gpio’ driver
22:07:47.252 → [0008.550] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
22:07:47.252 → [0008.560] I2C Bus Init done
22:07:47.252 → [0008.563] NCK carveout not present
22:07:47.252 → [0008.567] shim_invoke: No NCT, Calling dts updates
22:07:47.252 → [0008.578] Find /i2c@7000c000’s alias i2c0
22:07:47.252 → [0008.582] get eeprom at 1-a0, size 256, type 0
22:07:47.252 → [0008.590] Find /i2c@7000c500’s alias i2c2
22:07:47.252 → [0008.594] get eeprom at 3-a0, size 256, type 0
22:07:47.252 → [0008.599] get eeprom at 3-ae, size 256, type 0
22:07:47.252 → [0008.603] pm_ids_update: Updating 1,a0, size 256, type 0
22:07:47.252 → [0008.608] I2C slave not started
22:07:47.252 → [0008.611] I2C write failed
22:07:47.252 → [0008.614] Writing offset failed
22:07:47.252 → [0008.617] eeprom_init: EEPROM read failed
22:07:47.252 → [0008.621] pm_ids_update: eeprom init failed
22:07:47.252 → [0008.625] pm_ids_update: Updating 3,a0, size 256, type 0
22:07:47.288 → [0008.655] pm_ids_update: The pm board id is 3448-0000-200
22:07:47.318 → [0008.662] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
22:07:47.318 → [0008.670] pm_ids_update: pm id update successful
22:07:47.318 → [0008.674] pm_ids_update: Updating 3,ae, size 256, type 0
22:07:47.318 → [0008.704] pm_ids_update: The pm board id is 3449-0000-200
22:07:47.352 → [0008.710] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
22:07:47.352 → [0008.718] pm_ids_update: pm id update successful
22:07:47.352 → [0008.748] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
22:07:47.493 → [0008.754] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
22:07:47.493 → [0008.762] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
22:07:47.493 → [0008.768] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
22:07:47.493 → [0008.776] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e4:40:66
22:07:47.493 → [0008.783] Plugin Manager: Parse ODM data 0x00084000
22:07:47.493 → [0008.793] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
22:07:47.493 → [0008.813] Find /i2c@7000c000’s alias i2c0
22:07:47.493 → [0008.817] get eeprom at 1-a0, size 256, type 0
22:07:47.493 → [0008.826] Find /i2c@7000c500’s alias i2c2
22:07:47.493 → [0008.830] get eeprom at 3-a0, size 256, type 0
22:07:47.493 → [0008.834] get eeprom at 3-ae, size 256, type 0
22:07:47.493 → [0008.839] pm_ids_update: Updating 1,a0, size 256, type 0
22:07:47.493 → [0008.844] I2C slave not started
22:07:47.493 → [0008.847] I2C write failed
22:07:47.493 → [0008.849] Writing offset failed
22:07:47.493 → [0008.852] eeprom_init: EEPROM read failed
22:07:47.493 → [0008.856] pm_ids_update: eeprom init failed
22:07:47.493 → [0008.861] pm_ids_update: Updating 3,a0, size 256, type 0
22:07:47.493 → [0008.891] pm_ids_update: The pm board id is 3448-0000-200
22:07:47.537 → [0008.897] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
22:07:47.537 → [0008.904] pm_ids_update: pm id update successful
22:07:47.537 → [0008.908] pm_ids_update: Updating 3,ae, size 256, type 0
22:07:47.537 → [0008.939] pm_ids_update: The pm board id is 3449-0000-200
22:07:47.569 → [0008.945] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
22:07:47.569 → [0008.952] pm_ids_update: pm id update successful
22:07:47.602 → [0008.982] Chip UID is 000000016441f8091000000012010500
22:07:47.641 → [0008.987] Add serial number:04215190129720000501 as DT property
22:07:47.641 → [0008.995] Applying platform configs
22:07:47.641 → [0009.001] platform-init is not present. Skipping
22:07:47.641 → [0009.006] calling apps_init()
22:07:47.675 → [0009.031] Found 12 GPT partitions in “sd0”
22:07:47.675 → [0009.035] Proceeding to Cold Boot
22:07:47.675 → [0009.038] starting app android_boot_app
22:07:47.675 → [0009.042] Device state: unlocked
22:07:47.675 → [0009.045] display console init
22:07:47.675 → [0009.053] could not find regulator
22:07:47.709 → [0009.077] hdmi cable not connected
22:07:47.743 → [0009.080] is_hdmi_needed: HDMI not connected, returning false
22:07:47.743 → [0009.089] hdmi is not connected
22:07:47.743 → [0009.092] sor0 is not supported
22:07:47.743 → [0009.095] display_console_init: no valid display out_type
22:07:47.743 → [0009.103] subnode volume_up is not found !
22:07:47.743 → [0009.107] subnode back is not found !
22:07:47.743 → [0009.110] subnode volume_down is not found !
22:07:47.743 → [0009.114] subnode menu is not found !
22:07:47.743 → [0009.118] Gpio keyboard init success
22:07:47.776 → [0009.163] found decompressor handler: lz4-legacy
22:07:47.810 → [0009.178] decompressing blob (type 1)…
22:07:47.810 → [0009.211] display_resolution: No display init
22:07:47.844 → [0009.216] Failed to retrieve display resolution
22:07:47.844 → [0009.220] Could not load/initialize BMP blob…ignoring
22:07:47.948 → [0009.273] decompressor handler not found
22:07:47.948 → [0009.277] load_firmware_blob: Firmware blob loaded, entries=2
22:07:47.948 → [0009.283] se_aes_verify_sbk_clear: Error
22:07:47.948 → [0009.286] bl_battery_charging: connected to external power supply
22:07:47.948 → [0009.293] xusb is supported
22:07:47.948 → [0009.299] error while finding nvidia,portmap
22:07:47.948 → [0009.305] could not find regulator
22:07:48.444 → [0009.808] xusb blob version 0 size 126464
22:07:48.444 → [0009.812] firmware size 126464
22:07:48.444 → [0009.817] Firmware timestamp: 0x59fc70d3, Version: 50.20 release
22:07:48.444 → [0009.826] xhci0: 64 bytes context size, 32-bit DMA
22:07:48.481 → [0009.866] usbus0: 5.0Gbps Super Speed USB v3.0
22:07:48.519 → [0009.886] uhub0: <Nvidia XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
22:07:49.148 → [0010.536] uhub0: 9 ports with 9 removable, self powered
22:07:50.242 → [0011.536] failed to get HID devices
22:07:50.242 → [0011.539] failed to init xhci or no usb device attached
22:07:50.242 → [0011.546] display_console_ioctl: No display init
22:07:50.242 → [0011.551] switch_backlight failed
22:07:50.242 → [0011.557] device_query_partition_size: failed to open partition sd0:MSC !
22:07:50.242 → [0011.564] MSC Partition not found
22:07:50.242 → [0011.570] device_query_partition_size: failed to open partition sd0:USP !
22:07:50.242 → [0011.577] USP partition read failed!
22:07:50.242 → [0011.580] blob_init: blob-partition USP header read failed
22:07:50.242 → [0011.586] android_boot Unable to update recovery partition
22:07:50.242 → [0011.591] kfs_getpartname: name = LNX
22:07:50.242 → [0011.595] Loading kernel from LNX
22:07:50.275 → [0011.654] Verifying boot image in OdmNonSecureSBK mode
22:07:50.342 → [0011.697] kernel load address: 0x80080000, size: 476936 bytes
22:07:50.342 → [0011.702] ramdisk load address: 0x84100000, size: 0 bytes
22:07:50.342 → [0011.708] load kernel from storage
22:07:50.342 → [0011.719] decompressor handler not found
22:07:50.513 → [0011.776] Successfully loaded kernel and ramdisk images
22:07:50.513 → [0011.782] display_resolution: No display init
22:07:50.513 → [0011.787] Failed to retrieve display resolution
22:07:50.513 → [0011.791] bmp blob is not loaded and initialized
22:07:50.513 → [0011.796] Failed to display boot-logo
22:07:50.513 → [0011.799] NCK carveout not present
22:07:50.513 → [0011.802] Skipping dts_overrides
22:07:50.513 → [0011.806] NCK carveout not present
22:07:50.513 → [0011.809] shim_invoke: No NCT, Calling dts updates
22:07:50.513 → [0011.820] Find /i2c@7000c000’s alias i2c0
22:07:50.513 → [0011.824] get eeprom at 1-a0, size 256, type 0
22:07:50.513 → [0011.833] Find /i2c@7000c500’s alias i2c2
22:07:50.513 → [0011.837] get eeprom at 3-a0, size 256, type 0
22:07:50.513 → [0011.841] get eeprom at 3-ae, size 256, type 0
22:07:50.513 → [0011.845] pm_ids_update: Updating 1,a0, size 256, type 0
22:07:50.513 → [0011.851] I2C slave not started
22:07:50.513 → [0011.854] I2C write failed
22:07:50.513 → [0011.856] Writing offset failed
22:07:50.513 → [0011.859] eeprom_init: EEPROM read failed
22:07:50.513 → [0011.863] pm_ids_update: eeprom init failed
22:07:50.513 → [0011.867] pm_ids_update: Updating 3,a0, size 256, type 0
22:07:50.513 → [0011.897] pm_ids_update: The pm board id is 3448-0000-200
22:07:50.555 → [0011.904] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
22:07:50.555 → [0011.912] pm_ids_update: pm id update successful
22:07:50.555 → [0011.916] pm_ids_update: Updating 3,ae, size 256, type 0
22:07:50.555 → [0011.946] pm_ids_update: The pm board id is 3449-0000-200
22:07:50.582 → [0011.953] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
22:07:50.582 → [0011.960] pm_ids_update: pm id update successful
22:07:50.616 → [0011.991] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
22:07:50.857 → [0011.996] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
22:07:50.857 → [0012.004] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
22:07:50.857 → [0012.010] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
22:07:50.857 → [0012.019] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e4:40:66
22:07:50.857 → [0012.025] Plugin Manager: Parse ODM data 0x00084000
22:07:50.857 → [0012.036] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
22:07:50.857 → [0012.049] Add serial number:04215190129720000501 as DT property
22:07:50.857 → [0012.058] “bpmp” doesn’t exist, creating
22:07:50.857 → [0012.064] Updated bpmp info to DTB
22:07:50.857 → [0012.068] Updated initrd info to DTB
22:07:50.857 → [0012.072] “proc-board” doesn’t exist, creating
22:07:50.857 → [0012.078] Updated board info to DTB
22:07:50.857 → [0012.081] “pmu-board” doesn’t exist, creating
22:07:50.857 → [0012.087] Updated board info to DTB
22:07:50.857 → [0012.090] “display-board” doesn’t exist, creating
22:07:50.857 → [0012.096] Updated board info to DTB
22:07:50.857 → [0012.099] “reset” doesn’t exist, creating
22:07:50.857 → [0012.104] Updated reset info to DTB
22:07:50.857 → [0012.107] display_console_ioctl: No display init
22:07:50.857 → [0012.111] display_console_ioctl: No display init
22:07:50.857 → [0012.116] display_console_ioctl: No display init
22:07:50.857 → [0012.121] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000
22:07:50.857 → [0012.155] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
22:07:50.857 → [0012.166] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
22:07:50.857 → [0012.177] Updated bootarg info to DTB
22:07:50.857 → [0012.181] Adding uuid 000000016441f8091000000012010500 to DT
22:07:50.857 → [0012.190] device_query_partition_size: failed to open partition sd0:RP6 !
22:07:50.857 → [0012.197] RP6 partition read failed!
22:07:50.857 → [0012.202] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
22:07:50.857 → [0012.208] Updated memory info to DTB
22:07:50.857 → [0012.213] Updated system-lp0-disable info to DTB
22:07:50.857 → [0012.221] set vdd_core voltage to 1125 mv
22:07:50.857 → [0012.225] setting ‘vdd-core’ regulator to 1125000 micro volts
22:07:50.962 → [0012.246] could not find regulator
22:07:50.962 → [0012.250] Found secure-pmc; disable BPMP
22:07:50.962 →
22:07:50.962 →
22:07:50.962 → U-Boot 2016.07-g0eb73f4 (Mar 13 2019 - 00:21:24 -0700)
22:07:50.962 →
22:07:50.962 → TEGRA210
22:07:50.962 → Model: NVIDIA P3450-Porg
22:07:50.962 → Board: NVIDIA P3450-PORG
22:07:50.962 → DRAM: 4 GiB
22:07:51.208 → MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1
22:07:51.208 → Using default environment
22:07:51.208 →
22:07:51.208 → In: serial
22:07:51.208 → Out: serial
22:07:51.208 → Err: serial
22:07:51.208 → Net: No ethernet found.
22:07:51.519 → Hit any key to stop autoboot: 2 1 0
22:07:53.560 → switch to partitions #0, OK
22:07:53.560 → mmc1 is current device
22:07:54.368 → Scanning mmc 1:1…
22:07:54.868 → Found /boot/extlinux/extlinux.conf
22:07:54.868 → Retrieving file: /boot/extlinux/extlinux.conf
22:07:55.008 → 239 bytes read in 111 ms (2 KiB/s)
22:07:55.008 → p3450-porg eMMC boot options
22:07:55.008 → 1: primary kernel
22:07:55.008 → Enter choice: 1: primary kernel
22:07:57.988 → Retrieving file: /boot/initrd
22:07:58.128 → 0 bytes read in 86 ms (0 Bytes/s)
22:07:58.128 → Retrieving file: /boot/Image
22:07:59.658 → 34048008 bytes read in 1528 ms (21.2 MiB/s)
22:07:59.725 → append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 rootfstype=ext4 root=/dev/mmcblk0p1 rw rootwait
22:07:59.725 → ## Flattened Device Tree blob at 83100000
22:07:59.725 → Booting using the fdt blob at 0x83100000
22:07:59.725 → reserving fdt memory region: addr=80000000 size=20000
22:07:59.725 → Using Device Tree in place at 0000000083100000, end 0000000083173e9a
22:07:59.725 →
22:07:59.725 → Starting kernel …
22:07:59.725 →
22:08:00.775 →
22:08:00.950 → [ 0.000000] Booting Linux on physical CPU 0x0
22:08:01.312 → [ 0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-3531) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Wed Mar 13 00:32:22 PDT 2019
22:08:01.312 → [ 0.000000] Boot CPU: AArch64 Processor [411fd071]
22:08:01.312 → [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48,
22:08:01.312 → [ 0.000000] OF: fdt: - 80000000 , 7ee00000
22:08:01.312 → [ 0.000000] OF: fdt: - 100000000 , 7f200000
22:08:01.312 → [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node ‘fb0_carveout’: base 0x0000000000000000, size 0 MiB
22:08:01.312 → [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node ‘fb0_carveout’: base 0x0000000000000000, size 0 MiB
22:08:01.312 → [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node ‘fb1_carveout’: base 0x0000000000000000, size 0 MiB
22:08:01.312 → [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node ‘fb1_carveout’: base 0x0000000000000000, size 0 MiB
22:08:01.312 → [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout
22:08:01.312 → [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout
22:08:01.312 → [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops
22:08:01.312 → [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000
22:08:01.312 → [ 0.000000] psci: probing for conduit method from DT.
22:08:01.312 → [ 0.000000] psci: PSCIv1.0 detected in firmware.
22:08:01.312 → [ 0.000000] psci: Using standard PSCI v0.2 function IDs
22:08:01.312 → [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
22:08:01.312 → [ 0.000000] psci: SMC Calling Convention v1.1
22:08:01.312 → [ 0.000000] percpu: Embedded 23 pages/cpu @ffffffc0fefd2000 s53400 r8192 d32616 u94208
22:08:01.312 → [ 0.000000] CPU features: enabling workaround for ARM erratum 832075
22:08:01.312 → [ 0.000000] Speculative Store Bypass Disable mitigation not required
22:08:01.312 → [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544
22:08:01.312 → [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 rootfstype=ext4 root=/dev/mmcblk0p1 rw rootwait
22:08:01.312 → [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes
22:08:01.312 → [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes
22:08:01.312 → [ 0.000000] log_buf_len min size: 32768 bytes
22:08:01.312 → [ 0.000000] log_buf_len: 131072 bytes
22:08:01.312 → [ 0.000000] early log buf free: 29492(90%)
22:08:01.312 → [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
22:08:01.312 → [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
22:08:01.312 → [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
22:08:01.312 → [ 0.000000] Memory: 3576064K/4159488K available (15166K kernel code, 2914K rwdata, 6616K rodata, 8512K init, 605K bss, 108288K reserved, 475136K cma-reserved)
22:08:01.312 → [ 0.000000] Virtual kernel memory layout:
22:08:01.312 → [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
22:08:01.312 → [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
22:08:01.312 → [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f50000 ( 15168 KB)
22:08:01.312 → [ 0.000000] .rodata : 0xffffff8008f50000 - 0xffffff80095d0000 ( 6656 KB)
22:08:01.312 → [ 0.000000] .init : 0xffffff80095d0000 - 0xffffff8009e20000 ( 8512 KB)
22:08:01.312 → [ 0.000000] .data : 0xffffff8009e20000 - 0xffffff800a0f8808 ( 2915 KB)
22:08:01.312 → [ 0.000000] .bss : 0xffffff800a0f8808 - 0xffffff800a18fe3c ( 606 KB)
22:08:01.312 → [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB)
22:08:01.664 → [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
22:08:01.664 → [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
22:08:01.664 → [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual)
22:08:01.664 → [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB)
22:08:01.664 → [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
22:08:01.664 → [ 0.000000] Preemptible hierarchical RCU implementation.
22:08:01.664 → [ 0.000000] Build-time adjustment of leaf fanout to 64.
22:08:01.664 → [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
22:08:01.664 → [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
22:08:01.664 → [ 0.000000] NR_IRQS:64 nr_irqs:64 0
22:08:01.664 → [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller
22:08:01.664 → [ 0.000000] t210 clock and reset probe
22:08:01.664 → [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1
22:08:01.664 → [ 0.000000] clk_cbus_recalc_rate: no gbus parent
22:08:01.664 → [ 0.000000] clk_cbus_recalc_rate: no gbus parent
22:08:01.664 → [ 0.000000] clk_cbus_recalc_rate: no gbus parent
22:08:01.664 → [ 0.000000] clk_cbus_recalc_rate: no gbus parent
22:08:01.664 → [ 0.000000] clk_cbus_recalc_rate: no gbus parent
22:08:01.664 → [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys).
22:08:01.664 → [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
22:08:01.664 → [ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
22:08:01.664 → [ 0.001487] Console: colour dummy device 80x25
22:08:01.664 → [ 0.002332] console [tty0] enabled
22:08:01.664 → [ 0.002359] kmemleak: Kernel memory leak detector disabled
22:08:01.664 → [ 0.002386] Calibrating delay loop (skipped), value calculated using timer frequency… 38.40 BogoMIPS (lpj=76800)
22:08:01.664 → [ 0.002413] pid_max: default: 32768 minimum: 301
22:08:01.664 → [ 0.002870] Security Framework initialized
22:08:01.664 → [ 0.003101] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
22:08:01.664 → [ 0.003121] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
22:08:01.664 → [ 0.004309] ftrace: allocating 46802 entries in 183 pages
22:08:01.664 → [ 0.175858] ASID allocator initialised with 65536 entries
22:08:01.664 → [ 0.211288] tegra-id: chipid=22117.
22:08:01.664 → [ 0.211326] tegra-id: opt_subrevision=0.
22:08:01.664 → [ 0.211354] Tegra Speedo/IDDQ fuse revision 4
22:08:01.664 → [ 0.211370] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2
22:08:01.664 → [ 0.211387] Tegra: CPU Process ID 0, SoC Process ID 0, GPU Process ID 0
22:08:01.664 → [ 0.211402] Tegra: CPU Speedo Value 2018, SoC Speedo Value 1914, GPU Speedo Value 2024
22:08:01.664 → [ 0.211423] Tegra: CPU IDDQ Value 1620, SoC IDDQ Value 1888, GPU IDDQ Value 2220
22:08:01.664 → [ 0.211458] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 0
22:08:01.664 → [ 0.211484] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/…/…/…/…/…/…/hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts
22:08:01.664 → [ 0.211518] DTB Build time: Mar 15 2019 09:52:07
22:08:01.664 → [ 0.261069] CPU1: Booted secondary processor [411fd071]
22:08:01.664 → [ 0.292965] CPU2: Booted secondary processor [411fd071]
22:08:01.664 → [ 0.324949] CPU3: Booted secondary processor [411fd071]
22:08:01.664 → [ 0.325043] Brought up 4 CPUs
22:08:01.664 → [ 0.325107] SMP: Total of 4 processors activated.
22:08:01.664 → [ 0.325125] CPU features: detected feature: 32-bit EL0 Support
22:08:01.664 → [ 0.325400] CPU: All CPU(s) started at EL2
22:08:01.664 → [ 0.325430] alternatives: patching kernel code
22:08:01.664 → [ 0.333423] devtmpfs: initialized
22:08:01.664 → [ 0.367927] Initilizing CustomIPI irq domain
22:08:01.664 → [ 0.368341] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
22:08:01.664 → [ 0.368386] futex hash table entries: 1024 (order: 4, 65536 bytes)
22:08:01.664 → [ 0.378848] pinctrl core: initialized pinctrl subsystem
22:08:01.664 → [ 0.379488] OS set in device tree is not L4T.
22:08:01.664 → [ 0.379900] regulator-dummy: no parameters
22:08:01.664 → [ 0.380179] Initializing plugin-manager
22:08:01.664 → [ 0.380338] Plugin module not found
22:08:01.664 → [ 0.380558] node /plugin-manager/fragement@0 match with board >=3448-0000-100
22:08:02.013 → [ 0.381125] node /plugin-manager/fragment@1 match with board >=3448-0000-101
22:08:02.013 → [ 0.381882] node /plugin-manager/fragment@5 match with board 3449-0000-200
22:08:02.013 → [ 0.385133] NET: Registered protocol family 16
22:08:02.013 → [ 0.386432] pstore: using zlib compression
22:08:02.013 → [ 0.387065] console [pstore-1] enabled
22:08:02.013 → [ 0.387081] pstore: Registered ramoops as persistent store backend
22:08:02.013 → [ 0.387099] ramoops: attached 0x200000@0xb0000000, ecc: 0/0
22:08:02.013 → [ 0.401086] cpuidle: using governor menu
22:08:02.013 → [ 0.404907] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver
22:08:02.013 → [ 0.406418] vdso: 2 pages (1 code @ ffffff8008f57000, 1 data @ ffffff8009e24000)
22:08:02.013 → [ 0.406463] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
22:08:02.013 → [ 0.409490] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations
22:08:02.013 → [ 0.411044] tegra_bpmp_of_clk_init: EMC proxy not found.
22:08:02.013 → [ 0.412013] tegra_powergate_init: DONE
22:08:02.013 → [ 0.412051] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/…/…/…/…/…/…/hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts
22:08:02.013 → [ 0.412088] DTB Build time: Mar 15 2019 09:52:07
22:08:02.013 → [ 0.413773] Tegra reboot handler registered.
22:08:02.013 → [ 0.418093] iommu: Adding device tegra-carveouts to group 0
22:08:02.013 → [ 0.418269] platform tegra-carveouts: domain=ffffffc0f9bf0318 allocates as[0]=ffffffc0f9b980a8
22:08:02.013 → [ 0.418638] iommu: Adding device smmu_test to group 1
22:08:02.013 → [ 0.418704] platform smmu_test: domain=ffffffc0f9bf0558 allocates as[0]=ffffffc0f9b98110
22:08:02.013 → [ 0.419532] mc: mapped MMIO address: 0xffffff800802e000 → 0x70019000
22:08:02.013 → [ 0.419609] mc: mapped MMIO address: 0xffffff8008065000 → 0x7001c000
22:08:02.013 → [ 0.419683] mc: mapped MMIO address: 0xffffff8008079000 → 0x7001d000
22:08:02.013 → [ 0.419706] nv-tegra-mc 70019000.mc: No mssnvlink node
22:08:02.013 → [ 0.419741] mc-err: mcerr ops are set to t21x
22:08:02.013 → [ 0.429477] iommu: Adding device 70090000.xusb to group 2
22:08:02.013 → [ 0.429787] iommu: Adding device 70006000.serial to group 3
22:08:02.013 → [ 0.429883] platform 70006000.serial: domain=ffffffc0f947e6d8 allocates as[0]=ffffffc0f9b98178
22:08:02.013 → [ 0.430301] iommu: Adding device 70006040.serial to group 4
22:08:02.013 → [ 0.430592] iommu: Adding device 70006200.serial to group 5
22:08:02.013 → [ 0.430824] iommu: Adding device sound to group 6
22:08:02.013 → [ 0.430890] platform sound: domain=ffffffc0f947ec18 allocates as[0]=ffffffc0f9b981e0
22:08:02.013 → [ 0.431455] iommu: Adding device 7000d400.spi to group 7
22:08:02.013 → [ 0.431746] iommu: Adding device 7000d600.spi to group 8
22:08:02.013 → [ 0.432035] iommu: Adding device 70410000.spi to group 9
22:08:02.013 → [ 0.432356] iommu: Adding device 50000000.host1x to group 10
22:08:02.013 → [ 0.432644] iommu: Adding device 54080000.vi to group 11
22:08:02.013 → [ 0.433084] iommu: Adding device 54600000.isp to group 12
22:08:02.013 → [ 0.433369] iommu: Adding device 54680000.isp to group 13
22:08:02.013 → [ 0.433697] iommu: Adding device tegradc.0 to group 14
22:08:02.013 → [ 0.433771] platform tegradc.0: domain=ffffffc0f948bb58 allocates as[0]=ffffffc0f9b98248
22:08:02.013 → [ 0.434305] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000)
22:08:02.013 → [ 0.434640] iommu: Adding device tegradc.1 to group 15
22:08:02.013 → [ 0.434707] platform tegradc.1: domain=ffffffc0f948bd98 allocates as[0]=ffffffc0f9b982b0
22:08:02.013 → [ 0.435238] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000)
22:08:02.013 → [ 0.435503] iommu: Adding device 54340000.vic to group 16
22:08:02.013 → [ 0.435725] iommu: Adding device 544c0000.nvenc to group 17
22:08:02.013 → [ 0.435936] iommu: Adding device 54500000.tsec to group 18
22:08:02.013 → [ 0.436159] iommu: Adding device 54100000.tsecb to group 19
22:08:02.013 → [ 0.436370] iommu: Adding device 54480000.nvdec to group 20
22:08:02.013 → [ 0.436595] iommu: Adding device 54380000.nvjpg to group 21
22:08:02.013 → [ 0.437750] iommu: Adding device 546c0000.i2c to group 22
22:08:02.013 → [ 0.438094] iommu: Adding device 57000000.gpu to group 23
22:08:02.013 → [ 0.438159] platform 57000000.gpu: domain=ffffffc0f9495d98 allocates as[0]=ffffffc0f9b98318
22:08:02.013 → [ 0.438217] platform 57000000.gpu: domain=ffffffc0f9495d98 allocates as[1]=ffffffc0f9b98380
22:08:02.362 → [ 0.438279] platform 57000000.gpu: domain=ffffffc0f9495d98 allocates as[2]=ffffffc0f9b983e8
22:08:02.362 → [ 0.438337] platform 57000000.gpu: domain=ffffffc0f9495d98 allocates as[3]=ffffffc0f9b98450
22:08:02.362 → [ 0.439249] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled.
22:08:02.362 → [ 0.439288] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present
22:08:02.362 → [ 0.439315] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET
22:08:02.362 → [ 0.439335] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM
22:08:02.362 → [ 0.439352] tegra-pmc: ### PMC reset status reg: 0x0
22:08:02.362 → [ 0.489145] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered
22:08:02.362 → [ 0.489181] tegra-pmc: Clear bootloader IO dpd settings
22:08:02.362 → [ 0.489216] tegra-pmc 7000e400.pmc: IO padctrl driver initialized
22:08:02.362 → [ 0.489295] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands
22:08:02.362 → [ 0.489613] iommu: Adding device 70012000.se to group 24
22:08:02.362 → [ 0.490481] iommu: Adding device 7000c000.i2c to group 25
22:08:02.362 → [ 0.490809] iommu: Adding device 7000c400.i2c to group 26
22:08:02.362 → [ 0.491141] iommu: Adding device 7000c500.i2c to group 27
22:08:02.362 → [ 0.491458] iommu: Adding device 7000c700.i2c to group 28
22:08:02.362 → [ 0.491815] iommu: Adding device 7000d000.i2c to group 29
22:08:02.362 → [ 0.492138] iommu: Adding device 7000d100.i2c to group 30
22:08:02.362 → [ 0.492494] iommu: Adding device sdhci-tegra.0 to group 31
22:08:02.362 → [ 0.492568] platform sdhci-tegra.0: domain=ffffffc0f9524f18 allocates as[0]=ffffffc0f9b984b8
22:08:02.362 → [ 0.493517] iommu: Adding device 700d0000.xudc to group 32
22:08:02.362 → [ 0.499706] vdd-ac-bat: 5000 mV
22:08:02.362 → [ 0.500181] vdd-5v0-sys: 5000 mV
22:08:02.362 → [ 0.501381] vdd-5v0-hdmi: supplied by vdd-5v0-sys
22:08:02.362 → [ 0.501475] vdd-5v0-hdmi: 5000 mV
22:08:02.362 → [ 0.501950] vdd-1v8: 1800 mV
22:08:02.362 → [ 0.502464] vdd-fan: supplied by vdd-5v0-sys
22:08:02.362 → [ 0.502521] vdd-fan: 5000 mV
22:08:02.362 → [ 0.503009] vdd-usb-vbus: supplied by vdd-5v0-sys
22:08:02.362 → [ 0.503084] vdd-usb-vbus: 5000 mV
22:08:02.362 → [ 0.503683] vdd-usb-vbus2: 5000 mV
22:08:02.362 → [ 0.533905] HugeTLB registered 2 MB page size, pre-allocated 0 pages
22:08:02.362 → [ 0.536381] GPIO line 151 (camera-control-output-low) hogged as output/low
22:08:02.362 → [ 0.536757] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio)
22:08:02.362 → [ 0.544796] eventlib_kernel: keventlib is initialized, test id: 0
22:08:02.362 → [ 0.546659] SCSI subsystem initialized
22:08:02.362 → [ 0.547282] usbcore: registered new interface driver usbfs
22:08:02.362 → [ 0.547357] usbcore: registered new interface driver hub
22:08:02.362 → [ 0.547451] usbcore: registered new device driver usb
22:08:02.362 → [ 0.551538] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8
22:08:02.362 → [ 0.553322] random: fast init done
22:08:02.362 → [ 0.556481] vdd-core: 600 <–> 1162 mV at 1125 mV
22:08:02.362 → [ 0.557780] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV
22:08:02.362 → [ 0.560335] vdd-ddr-1v1: 1150 mV
22:08:02.362 → [ 0.565082] vdd-pre-reg-1v35: 1350 mV
22:08:02.362 → [ 0.569083] vdd-1v8: 1800 mV
22:08:02.362 → [ 0.569350] vdd-1v8: Failed to create debugfs directory
22:08:02.362 → [ 0.573081] avdd-sys-1v2: 1200 mV
22:08:02.362 → [ 0.577083] vdd-pex-1v0: 1050 mV
22:08:02.362 → [ 0.577856] vddio-sdmmc-ap: 1800 <–> 3300 mV at 3300 mV
22:08:02.362 → [ 0.578498] max77620-ldo3: at 3100 mV
22:08:02.362 → [ 0.581085] vdd-rtc: 850 <–> 1100 mV at 1000 mV
22:08:02.362 → [ 0.581732] max77620-ldo5: at 3100 mV
22:08:02.362 → [ 0.582374] max77620-ldo6: at 2800 mV
22:08:02.362 → [ 0.585084] avdd-1v05-pll: 1050 mV
22:08:02.362 → [ 0.589082] avdd-io-hdmi-dp: 1050 mV
22:08:02.362 → [ 0.590649] GPIO line 505 (spmic-default-output-high) hogged as output/high
22:08:02.362 → [ 0.590938] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio)
22:08:02.362 → [ 0.593012] max77620 4-003c: max77620 probe successful
22:08:02.362 → [ 0.595253] i2c i2c-6: Unbalanced pm_runtime_enable!
22:08:02.362 → [ 0.595813] media: Linux media interface: v0.10
22:08:02.362 → [ 0.595880] Linux video capture interface: v2.00
22:08:02.362 → [ 0.596785] pps_core: LinuxPPS API ver. 1 registered
22:08:02.362 → [ 0.596812] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
22:08:02.362 → [ 0.596854] PTP clock support registered
22:08:02.362 → [ 0.600147] tegra_fiq_debugger_init: found FIQ source (IRQ 98)
22:08:02.677 → [ 0.606398] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table
22:08:02.677 → [ 0.607185] Advanced Linux Sound Architecture Driver Initialized.
22:08:02.677 → [ 0.607824] Bluetooth: Core ver 2.22
22:08:02.677 → [ 0.607892] NET: Registered protocol family 31
22:08:02.677 → [ 0.607909] Bluetooth: HCI device and connection manager initialized
22:08:02.677 → [ 0.607935] Bluetooth: HCI socket layer initialized
22:08:02.677 → [ 0.607956] Bluetooth: L2CAP socket layer initialized
22:08:02.677 → [ 0.607994] Bluetooth: SCO socket layer initialized
22:08:02.677 → [ 0.609721] tegra210_dvfs: no clock found for sdmmc2_ddr
22:08:02.677 → [ 0.609758] tegra210_dvfs: no clock found for sdmmc4_ddr
22:08:02.677 → [ 0.609820] tegra210_dvfs: no clock found for sdmmc1_ddr
22:08:02.677 → [ 0.609848] tegra210_dvfs: no clock found for sdmmc3_ddr
22:08:02.677 → [ 0.612382] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe
22:08:02.677 → [ 0.613719] vdd-3v3-sys: supplied by vdd-5v0-sys
22:08:02.677 → [ 0.613801] vdd-3v3-sys: 3300 mV
22:08:02.677 → [ 0.614071] vdd-1v8: supplied by vdd-3v3-sys
22:08:02.677 → [ 0.617159] vdd-usb-vbus2: supplied by vdd-3v3-sys
22:08:02.677 → [ 0.617654] vdd-3v3-sd: supplied by vdd-3v3-sys
22:08:02.677 → [ 0.617705] vdd-3v3-sd: 3300 mV
22:08:02.677 → [ 0.618925] avdd-io-edp-1v05: supplied by avdd-1v05-pll
22:08:02.677 → [ 0.618980] avdd-io-edp-1v05: 1050 mV
22:08:02.677 → [ 0.619475] vdd-usb-hub-en: supplied by vdd-1v8
22:08:02.677 → [ 0.619526] vdd-usb-hub-en: 5000 mV
22:08:02.677 → [ 0.620859] camchar: rtcpu character device driver loaded
22:08:02.677 → [ 0.621612] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0
22:08:02.677 → [ 0.622930] clocksource: Switched to clocksource arch_sys_counter
22:08:02.677 → [ 0.662185] VFS: Disk quotas dquot_6.6.0
22:08:02.677 → [ 0.662346] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
22:08:02.677 → [ 0.662869] nvmap_heap_init: nvmap_heap_init: created heap block cache
22:08:02.677 → [ 0.663354] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000
22:08:02.677 → [ 0.663406] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000)
22:08:02.677 → [ 0.663614] cma: enabled page replacement for spfn=d7000, epfn=f0000
22:08:02.677 → [ 0.663642] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful
22:08:02.677 → [ 0.663669] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout
22:08:02.677 → [ 0.663719] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048
22:08:02.677 → [ 0.663745] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout
22:08:02.677 → [ 0.663777] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways
22:08:02.677 → [ 0.663799] nvmap_page_pool_init: Total RAM pages: 1012800
22:08:02.677 → [ 0.663817] nvmap_page_pool_init: nvmap page pool size: 126600 pages (494 MB)
22:08:02.677 → [ 0.663926] nvmap_background_zero_thread: PP zeroing thread starting.
22:08:02.677 → [ 0.664415] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB)
22:08:02.677 → [ 0.665353] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB)
22:08:02.677 → [ 0.673623] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm
22:08:02.677 → [ 0.674037] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm
22:08:02.677 → [ 0.674306] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm
22:08:02.677 → [ 0.674535] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm
22:08:02.677 → [ 0.674727] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die
22:08:02.677 → [ 0.675056] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz
22:08:02.677 → [ 0.675078] pre_t19x_iso_plat_init(): max_iso_bw=33280000KB
22:08:02.677 → [ 0.675520] NET: Registered protocol family 2
22:08:02.677 → [ 0.676489] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
22:08:02.677 → [ 0.676729] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
22:08:02.677 → [ 0.677232] TCP: Hash tables configured (established 32768 bind 32768)
22:08:02.677 → [ 0.677394] UDP hash table entries: 2048 (order: 4, 65536 bytes)
22:08:02.677 → [ 0.677494] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
22:08:02.677 → [ 0.677934] NET: Registered protocol family 1
22:08:03.026 → [ 0.678741] RPC: Registered named UNIX socket transport module.
22:08:03.026 → [ 0.678771] RPC: Registered udp transport module.
22:08:03.026 → [ 0.678788] RPC: Registered tcp transport module.
22:08:03.026 → [ 0.678805] RPC: Registered tcp NFSv4.1 backchannel transport module.
22:08:03.026 → [ 0.679104] Trying to unpack rootfs image as initramfs…
22:08:03.026 → [ 0.688440] host1x 50000000.host1x: initialized
22:08:03.026 → [ 0.690226] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
22:08:03.026 → [ 0.693419] audit: initializing netlink subsys (disabled)
22:08:03.026 → [ 0.693532] audit: type=2000 audit(0.543:1): initialized
22:08:03.026 → [ 0.694279] workingset: timestamp_bits=46 max_order=20 bucket_order=0
22:08:03.026 → [ 0.704405] squashfs: version 4.0 (2009/01/31) Phillip Lougher
22:08:03.026 → [ 0.705926] ntfs: driver 2.1.32 [Flags: R/W].
22:08:03.026 → [ 0.706727] 9p: Installing v9fs 9p2000 file system support
22:08:03.026 → [ 0.709938] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240)
22:08:03.026 → [ 0.710097] io scheduler noop registered
22:08:03.026 → [ 0.710428] io scheduler cfq registered (default)
22:08:03.026 → [ 0.713308] gic 702f9000.agic: GIC IRQ controller registered
22:08:03.026 → [ 0.716134] iommu: Adding device 702ef000.adsp to group 33
22:08:03.026 → [ 0.722866] iommu: Adding device aconnect@702c0000:adsp_audio to group 34
22:08:03.026 → [ 0.723086] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered
22:08:03.026 → [ 0.723761] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x7269c10
22:08:03.026 → [ 0.723796] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4
22:08:03.026 → [ 0.725407] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb
22:08:03.026 → [ 0.725539] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb
22:08:03.026 → [ 0.725660] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb
22:08:03.026 → [ 0.725877] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1
22:08:03.026 → [ 0.725990] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4
22:08:03.026 → [ 0.726103] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4
22:08:03.026 → [ 0.726213] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4
22:08:03.026 → [ 0.726322] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4
22:08:03.026 → [ 0.726426] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb
22:08:03.026 → [ 0.726538] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb
22:08:03.026 → [ 0.732951] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops
22:08:03.026 → [ 0.734297] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000
22:08:03.026 → [ 0.736204] tegra-pcie 1003000.pcie-controller: 4x1, 1x1 configuration
22:08:03.026 → [ 0.737515] tegra-pcie 1003000.pcie-controller: PCIE: Enable power rails
22:08:03.026 → [ 0.737868] tegra-pcie 1003000.pcie-controller: probing port 0, using 4 lanes
22:08:03.026 → [ 0.739092] tegra-pcie 1003000.pcie-controller: probing port 1, using 1 lanes
22:08:03.026 → [ 0.739358] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe
22:08:03.026 → [ 0.739616] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=750000, max_bw=1500000
22:08:03.026 → [ 0.739885] Adding domain tsec-pd to PM domain host1x-pd
22:08:03.026 → [ 0.742808] tsec 54500000.tsec: initialized
22:08:03.026 → [ 0.744298] tsec 54100000.tsecb: initialized
22:08:03.026 → [ 0.745000] Adding domain nvdec-pd to PM domain host1x-pd
22:08:03.026 → [ 0.748124] nvdec 54480000.nvdec: initialized
22:08:03.026 → [ 0.749252] Adding domain vic03-pd to PM domain host1x-pd
22:08:03.026 → [ 0.749454] Adding domain msenc-pd to PM domain host1x-pd
22:08:03.026 → [ 0.749636] Adding domain nvjpg-pd to PM domain host1x-pd
22:08:03.026 → [ 0.753366] falcon 54340000.vic: initialized
22:08:03.026 → [ 0.754599] falcon 544c0000.nvenc: initialized
22:08:03.026 → [ 0.756002] falcon 54380000.nvjpg: initialized
22:08:03.026 → [ 0.760616] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1
22:08:03.026 → [ 0.760740] display board info: id 0x0, fab 0x0
22:08:03.371 → [ 0.760812] generic_infoframe_type: 0x87
22:08:03.371 → [ 0.760947] tegradc tegradc.0: DT parsed successfully
22:08:03.371 → [ 0.761012] tegradc tegradc.0: Display dc.ffffff800ab40000 registered with id=0
22:08:03.371 → [ 0.764287] tegradc tegradc.0: probed
22:08:03.371 → [ 0.768828] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels
22:08:03.371 → [ 0.773469] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 10 channels
22:08:03.371 → [ 0.774353] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized
22:08:03.371 → [ 0.774702] kfuse 7000fc00.kfuse: initialized
22:08:03.371 → [ 0.776229] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available
22:08:03.371 → [ 0.777280] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0
22:08:03.371 → [ 0.778595] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now
22:08:03.371 → [ 0.778638] vdd-cpu: 708 <–> 1322 mV at 708 mV
22:08:03.371 → [ 0.779193] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed
22:08:03.371 → [ 0.780951] vdd-gpu: applied init 1000000uV constraint
22:08:03.371 → [ 0.781003] vdd-gpu: 708 <–> 1323 mV at 997 mV
22:08:03.371 → [ 0.781420] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed
22:08:03.371 → [ 0.786078] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
22:08:03.371 → [ 0.786264] No Device Node present for smmu client: serial8250 !!
22:08:03.371 → [ 0.786293] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000)
22:08:03.371 → [ 0.786409] iommu: Adding device serial8250 to group 35
22:08:03.371 → [ 0.789772] console [ttyS0] disabled
22:08:03.371 → [ 0.789920] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra
22:08:03.371 → [ 1.263942] tegra-pcie 1003000.pcie-controller: link 0 down, retrying
22:08:03.371 → [ 1.668272] tegra-pcie 1003000.pcie-controller: link 0 down, retrying
22:08:03.371 → [ 2.072628] tegra-pcie 1003000.pcie-controller: link 0 down, retrying
22:08:03.371 → [ 2.074645] tegra-pcie 1003000.pcie-controller: link 0 down, ignoring
22:08:03.371 → [ 2.075085] tegra-pcie 1003000.pcie-controller: PCI host bridge to bus 0000:00
22:08:03.371 → [ 2.075097] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
22:08:03.371 → [ 2.075101] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff]
22:08:03.371 → [ 2.075107] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref]
22:08:03.371 → [ 2.075112] pci_bus 0000:00: root bus resource [bus 00-ff]
22:08:03.371 → [ 2.075520] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
22:08:03.371 → [ 2.087121] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff]
22:08:03.371 → [ 2.087126] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff]
22:08:03.371 → [ 2.087137] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff 64bit]
22:08:03.371 → [ 2.087164] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff 64bit]
22:08:03.371 → [ 2.087187] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff]
22:08:03.371 → [ 2.087199] pci 0000:00:02.0: PCI bridge to [bus 01]
22:08:03.371 → [ 2.087205] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]
22:08:03.371 → [ 2.087212] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff]
22:08:03.371 → [ 2.087958] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt
22:08:03.371 → [ 2.087963] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
22:08:03.371 → [ 3.137639] console [ttyS0] enabled
22:08:03.371 → [ 3.138036] Console: switching to colour frame buffer device 80x30
22:08:03.371 → [ 3.139165] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART
22:08:03.371 → [ 3.139532] serial-tegra 70006200.serial: RX in PIO mode
22:08:03.371 → [ 3.139640] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART
22:08:03.371 → [ 3.140719] [drm] Initialized
22:08:03.371 → [ 3.168167] brd: module loaded
22:08:03.371 → [ 3.177382] tegradc tegradc.0: fb registered
22:08:03.371 → [ 3.182709] loop: module loaded
22:08:03.371 → [ 3.183318] tegradc tegradc.1: disp1 connected to head1->/host1x/sor
22:08:04.221 → [ 3.183390] tegradc tegradc.1: No lt-data, using default setting
22:08:04.221 → [ 3.183414] tegradc tegradc.1: No hpd-gpio in DT
22:08:04.221 → [ 3.183444] tegradc tegradc.1: DT parsed successfully
22:08:04.221 → [ 3.183497] tegradc tegradc.1: Display dc.ffffff800f4c0000 registered with id=1
22:08:04.221 → [ 3.184905] tegradc tegradc.1: dpd enable lookup fail:-19
22:08:04.221 → [ 3.691783] tegradc tegradc.1: probed
22:08:04.221 → [ 3.692121] Host read timeout at address 545c00c4
22:08:04.221 → [ 3.729209] tegradc tegradc.1: fb registered
22:08:04.221 → [ 3.729340] tegra_profiler: version: 1.132, samples/io: 46/26
22:08:04.221 → [ 3.729495] tegra_profiler: auth: init
22:08:04.221 → [ 3.730869] THERMAL EST: found 2 subdevs
22:08:04.221 → [ 3.730876] THERMAL EST num_resources: 0
22:08:04.221 → [ 3.730881] [THERMAL EST subdev 0]
22:08:04.221 → [ 3.730887] [THERMAL EST subdev 1]
22:08:04.221 → [ 3.731386] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est
22:08:04.221 → [ 3.731388] THERMAL EST: thz register success.
22:08:04.221 → [ 3.731549] THERMAL EST: end of probe, return err: 0
22:08:04.221 → [ 3.732731] hisi_sas: driver version v1.6
22:08:04.221 → [ 3.736815] tegra-qspi 70410000.spi: Prod settings list not found
22:08:04.221 → [ 3.738036] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes)
22:08:04.221 → [ 3.738044] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0
22:08:04.221 → [ 3.741106] libphy: Fixed MDIO Bus: probed
22:08:04.221 → [ 3.741711] tun: Universal TUN/TAP device driver, 1.6
22:08:04.221 → [ 3.741713] tun: (C) 1999-2004 Max Krasnyansky maxk@qualcomm.com
22:08:04.221 → [ 3.743133] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
22:08:04.221 → [ 3.743136] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
22:08:04.221 → [ 3.743193] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
22:08:04.221 → [ 3.743196] igb: Copyright (c) 2007-2014 Intel Corporation.
22:08:04.221 → [ 3.743252] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
22:08:04.221 → [
I just realized the log got cut off, but this is the full log right up to the loading of the Ubuntu setup screen (graphical). No further messages beyond this.
[url]https://gist.github.com/jsyang/cad4ce745fbf47f054091bc80f83de54[/url]
I have exact the same problem with the same configuration( Intel 8265NGW card). Have you figured out any solution yet? All USB ports suddenly didn’t work. I tried to re-format the SD card, but the problem still exists. I can use Bluetooth mouse driven by the Intel WIFI card. I notice when it shutdown, there are constantly popping up error messages USB port “over current”.
I exported the dmesg shown as following:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-3531) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Wed Mar 13 00:32:22 PDT 2019
[ 0.000000] Boot CPU: AArch64 Processor [411fd071]
[ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48,
[ 0.000000] OF: fdt: - 80000000 , 7ee00000
[ 0.000000] OF: fdt: - 100000000 , 7f200000
[ 0.000000] Found tegra_fbmem: 00800000@92cb6000
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node ‘fb0_carveout’: base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node ‘fb0_carveout’: base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node ‘fb1_carveout’: base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node ‘fb1_carveout’: base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout
[ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout
[ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops
[ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000
[ 0.000000] On node 0 totalpages: 1039872
[ 0.000000] DMA zone: 8192 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 519168 pages, LIFO batch:31
[ 0.000000] Normal zone: 8136 pages used for memmap
[ 0.000000] Normal zone: 520704 pages, LIFO batch:31
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 23 pages/cpu @ffffffc0fefd2000 s53400 r8192 d32616 u94208
[ 0.000000] pcpu-alloc: s53400 r8192 d32616 u94208 alloc=23*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] CPU features: enabling workaround for ARM erratum 832075
[ 0.000000] Speculative Store Bypass Disable mitigation not required
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544
[ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x800000@0x92cb6000 is_hdmi_initialised=1 root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 rootfstype=ext4 root=/dev/mmcblk0p1 rw rootwait
[ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes
[ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes
[ 0.000000] log_buf_len min size: 32768 bytes
[ 0.000000] log_buf_len: 131072 bytes
[ 0.000000] early log buf free: 29384(89%)
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Memory: 3567872K/4159488K available (15166K kernel code, 2914K rwdata, 6616K rodata, 8512K init, 605K bss, 116480K reserved, 475136K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f50000 ( 15168 KB)
[ 0.000000] .rodata : 0xffffff8008f50000 - 0xffffff80095d0000 ( 6656 KB)
[ 0.000000] .init : 0xffffff80095d0000 - 0xffffff8009e20000 ( 8512 KB)
[ 0.000000] .data : 0xffffff8009e20000 - 0xffffff800a0f8808 ( 2915 KB)
[ 0.000000] .bss : 0xffffff800a0f8808 - 0xffffff800a18fe3c ( 606 KB)
[ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB)
[ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller
[ 0.000000] t210 clock and reset probe
[ 0.000000] boot misc1 0x90000000: expected 0x10000000
[ 0.000000] (comparison mask = 0xf8000000)
[ 0.000000] boot misc2 0x0: expected 0xf6e0f620
[ 0.000000] (comparison mask = 0xffffffff)
[ 0.000000] boot misc3 0xf5c1: expected 0x10000
[ 0.000000] (comparison mask = 0xffffffff)
[ 0.000000] PLL_D2 already enabled. Postponing set full defaults
[ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.001519] Console: colour dummy device 80x25
[ 0.002462] console [tty0] enabled
[ 0.002487] kmemleak: Kernel memory leak detector disabled
[ 0.002517] Calibrating delay loop (skipped), value calculated using timer frequency… 38.40 BogoMIPS (lpj=76800)
[ 0.002545] pid_max: default: 32768 minimum: 301
[ 0.003009] Security Framework initialized
[ 0.003243] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.003263] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.004523] ftrace: allocating 46802 entries in 183 pages
[ 0.176041] sched-energy: CPU device node has no sched-energy-costs
[ 0.176076] ASID allocator initialised with 65536 entries
[ 0.215645] tegra-id: chipid=22117.
[ 0.215696] tegra-id: opt_subrevision=0.
[ 0.215725] Tegra Speedo/IDDQ fuse revision 4
[ 0.215740] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2
[ 0.215756] Tegra: CPU Process ID 1, SoC Process ID 1, GPU Process ID 0
[ 0.215772] Tegra: CPU Speedo Value 2134, SoC Speedo Value 2038, GPU Speedo Value 2142
[ 0.215792] Tegra: CPU IDDQ Value 2668, SoC IDDQ Value 3036, GPU IDDQ Value 3755
[ 0.215825] Tegra Revision: A02 SKU: 0x8f CPU Process: 1 SoC Process: 1
[ 0.215851] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/…/…/…/…/…/…/hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts
[ 0.215886] DTB Build time: Mar 15 2019 09:52:07
[ 0.265081] CPU1: Booted secondary processor [411fd071]
[ 0.296994] CPU2: Booted secondary processor [411fd071]
[ 0.328970] CPU3: Booted secondary processor [411fd071]
[ 0.329071] Brought up 4 CPUs
[ 0.329137] SMP: Total of 4 processors activated.
[ 0.329155] CPU features: detected feature: 32-bit EL0 Support
[ 0.329435] CPU: All CPU(s) started at EL2
[ 0.329466] alternatives: patching kernel code
[ 0.337854] devtmpfs: initialized
[ 0.372145] Initilizing CustomIPI irq domain
[ 0.372627] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.372673] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.384158] pinctrl core: initialized pinctrl subsystem
[ 0.384845] OS set in device tree is not L4T.
[ 0.385311] regulator-dummy: no parameters
[ 0.385607] Initializing plugin-manager
[ 0.385762] Plugin module not found
[ 0.385981] node /plugin-manager/fragement@0 match with board >=3448-0000-100
[ 0.386520] node /plugin-manager/fragment@1 match with board >=3448-0000-101
[ 0.387296] node /plugin-manager/fragment@5 match with board 3449-0000-200
[ 0.390568] NET: Registered protocol family 16
[ 0.392028] pstore: using zlib compression
[ 0.392784] console [pstore-1] enabled
[ 0.392801] pstore: Registered ramoops as persistent store backend
[ 0.392819] ramoops: attached 0x200000@0xb0000000, ecc: 0/0
[ 0.408240] cpuidle: using governor menu
[ 0.412295] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver
[ 0.413896] vdso: 2 pages (1 code @ ffffff8008f57000, 1 data @ ffffff8009e24000)
[ 0.413941] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.416827] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations
[ 0.418431] tegra_bpmp_of_clk_init: EMC proxy not found.
[ 0.419387] tegra_powergate_init: DONE
[ 0.419428] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/…/…/…/…/…/…/hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts
[ 0.419465] DTB Build time: Mar 15 2019 09:52:07
[ 0.421189] Tegra reboot handler registered.
[ 0.425619] iommu: Adding device tegra-carveouts to group 0
[ 0.425767] platform tegra-carveouts: domain=ffffffc0f9b89f18 allocates as[0]=ffffffc0f9bac0a8
[ 0.426140] iommu: Adding device smmu_test to group 1
[ 0.426219] platform smmu_test: domain=ffffffc0f9b96198 allocates as[0]=ffffffc0f9bac110
[ 0.427051] mc: mapped MMIO address: 0xffffff800802e000 → 0x70019000
[ 0.427123] mc: mapped MMIO address: 0xffffff8008065000 → 0x7001c000
[ 0.427210] mc: mapped MMIO address: 0xffffff8008079000 → 0x7001d000
[ 0.427232] nv-tegra-mc 70019000.mc: No mssnvlink node
[ 0.427265] mc-err: mcerr ops are set to t21x
[ 0.436939] iommu: Adding device 70090000.xusb to group 2
[ 0.437382] iommu: Adding device 70006000.serial to group 3
[ 0.437484] platform 70006000.serial: domain=ffffffc0f948b618 allocates as[0]=ffffffc0f9bac178
[ 0.437933] iommu: Adding device 70006040.serial to group 4
[ 0.438227] iommu: Adding device 70006200.serial to group 5
[ 0.438466] iommu: Adding device sound to group 6
[ 0.438529] platform sound: domain=ffffffc0f948bb58 allocates as[0]=ffffffc0f9bac1e0
[ 0.439121] iommu: Adding device 7000d400.spi to group 7
[ 0.439397] iommu: Adding device 7000d600.spi to group 8
[ 0.439687] iommu: Adding device 70410000.spi to group 9
[ 0.440014] iommu: Adding device 50000000.host1x to group 10
[ 0.440316] iommu: Adding device 54080000.vi to group 11
[ 0.440728] iommu: Adding device 54600000.isp to group 12
[ 0.441010] iommu: Adding device 54680000.isp to group 13
[ 0.441392] iommu: Adding device tegradc.0 to group 14
[ 0.441462] platform tegradc.0: domain=ffffffc0f94b0a98 allocates as[0]=ffffffc0f9bac248
[ 0.445728] platform tegradc.0: IOVA linear map 0x0000000092cb6000(800000)
[ 0.446142] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000)
[ 0.446491] iommu: Adding device tegradc.1 to group 15
[ 0.446559] platform tegradc.1: domain=ffffffc0f94b0cd8 allocates as[0]=ffffffc0f9bac2b0
[ 0.450762] platform tegradc.1: IOVA linear map 0x0000000092cb6000(800000)
[ 0.451173] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000)
[ 0.451438] iommu: Adding device 54340000.vic to group 16
[ 0.451677] iommu: Adding device 544c0000.nvenc to group 17
[ 0.451901] iommu: Adding device 54500000.tsec to group 18
[ 0.452114] iommu: Adding device 54100000.tsecb to group 19
[ 0.452327] iommu: Adding device 54480000.nvdec to group 20
[ 0.452571] iommu: Adding device 54380000.nvjpg to group 21
[ 0.453677] iommu: Adding device 546c0000.i2c to group 22
[ 0.454028] iommu: Adding device 57000000.gpu to group 23
[ 0.454098] platform 57000000.gpu: domain=ffffffc0f94dacd8 allocates as[0]=ffffffc0f9bac318
[ 0.454160] platform 57000000.gpu: domain=ffffffc0f94dacd8 allocates as[1]=ffffffc0f9bac380
[ 0.454225] platform 57000000.gpu: domain=ffffffc0f94dacd8 allocates as[2]=ffffffc0f9bac3e8
[ 0.454280] platform 57000000.gpu: domain=ffffffc0f94dacd8 allocates as[3]=ffffffc0f9bac450
[ 0.455188] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled.
[ 0.455230] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present
[ 0.455259] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET
[ 0.455280] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM
[ 0.455296] tegra-pmc: ### PMC reset status reg: 0x0
[ 0.505251] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered
[ 0.505284] tegra-pmc: Clear bootloader IO dpd settings
[ 0.505320] tegra-pmc 7000e400.pmc: IO padctrl driver initialized
[ 0.505400] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands
[ 0.505714] iommu: Adding device 70012000.se to group 24
[ 0.506511] iommu: Adding device 7000c000.i2c to group 25
[ 0.506781] iommu: Adding device 7000c400.i2c to group 26
[ 0.507055] iommu: Adding device 7000c500.i2c to group 27
[ 0.507329] iommu: Adding device 7000c700.i2c to group 28
[ 0.507632] iommu: Adding device 7000d000.i2c to group 29
[ 0.507904] iommu: Adding device 7000d100.i2c to group 30
[ 0.508223] iommu: Adding device sdhci-tegra.0 to group 31
[ 0.508296] platform sdhci-tegra.0: domain=ffffffc0f954be58 allocates as[0]=ffffffc0f9bac4b8
[ 0.509194] iommu: Adding device 700d0000.xudc to group 32
[ 0.513834] vdd-ac-bat: 5000 mV
[ 0.514225] vdd-5v0-sys: 5000 mV
[ 0.515216] vdd-5v0-hdmi: supplied by vdd-5v0-sys
[ 0.515302] vdd-5v0-hdmi: 5000 mV
[ 0.515723] vdd-1v8: 1800 mV
[ 0.516120] vdd-fan: supplied by vdd-5v0-sys
[ 0.516171] vdd-fan: 5000 mV
[ 0.516597] vdd-usb-vbus: supplied by vdd-5v0-sys
[ 0.516673] vdd-usb-vbus: 5000 mV
[ 0.517263] vdd-usb-vbus2: 5000 mV
[ 0.545973] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.548557] GPIO line 151 (camera-control-output-low) hogged as output/low
[ 0.549023] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio)
[ 0.557069] eventlib_kernel: keventlib is initialized, test id: 0
[ 0.557482] SCSI subsystem initialized
[ 0.557718] libata version 3.00 loaded.
[ 0.558008] usbcore: registered new interface driver usbfs
[ 0.558080] usbcore: registered new interface driver hub
[ 0.558174] usbcore: registered new device driver usb
[ 0.562298] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8
[ 0.563738] random: fast init done
[ 0.568438] vdd-core: 600 <–> 1162 mV at 1075 mV
[ 0.569753] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV
[ 0.572245] vdd-ddr-1v1: 1150 mV
[ 0.576297] vdd-pre-reg-1v35: 1350 mV
[ 0.580238] vdd-1v8: 1800 mV
[ 0.580521] vdd-1v8: Failed to create debugfs directory
[ 0.584237] avdd-sys-1v2: 1200 mV
[ 0.588242] vdd-pex-1v0: 1050 mV
[ 0.589033] vddio-sdmmc-ap: 1800 <–> 3300 mV at 3300 mV
[ 0.589685] max77620-ldo3: at 3100 mV
[ 0.592239] vdd-rtc: 850 <–> 1100 mV at 1000 mV
[ 0.592938] max77620-ldo5: at 3100 mV
[ 0.593609] max77620-ldo6: at 2800 mV
[ 0.596246] avdd-1v05-pll: 1050 mV
[ 0.600236] avdd-io-hdmi-dp: 1050 mV
[ 0.601872] GPIO line 505 (spmic-default-output-high) hogged as output/high
[ 0.602177] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio)
[ 0.604403] max77620 4-003c: max77620 probe successful
[ 0.606691] i2c i2c-6: Unbalanced pm_runtime_enable!
[ 0.607246] media: Linux media interface: v0.10
[ 0.607313] Linux video capture interface: v2.00
[ 0.608356] pps_core: LinuxPPS API ver. 1 registered
[ 0.608386] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
[ 0.608429] PTP clock support registered
[ 0.611769] tegra_fiq_debugger_init: found FIQ source (IRQ 98)
[ 0.618052] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table
[ 0.618902] Advanced Linux Sound Architecture Driver Initialized.
[ 0.619582] Bluetooth: Core ver 2.22
[ 0.619649] NET: Registered protocol family 31
[ 0.619667] Bluetooth: HCI device and connection manager initialized
[ 0.619695] Bluetooth: HCI socket layer initialized
[ 0.619719] Bluetooth: L2CAP socket layer initialized
[ 0.619756] Bluetooth: SCO socket layer initialized
[ 0.621398] tegra210_dvfs: no clock found for sdmmc2_ddr
[ 0.621436] tegra210_dvfs: no clock found for sdmmc4_ddr
[ 0.621493] tegra210_dvfs: no clock found for sdmmc1_ddr
[ 0.621519] tegra210_dvfs: no clock found for sdmmc3_ddr
[ 0.624194] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe
[ 0.625647] vdd-3v3-sys: supplied by vdd-5v0-sys
[ 0.625737] vdd-3v3-sys: 3300 mV
[ 0.626027] vdd-1v8: supplied by vdd-3v3-sys
[ 0.628303] vdd-usb-vbus2: supplied by vdd-3v3-sys
[ 0.628820] vdd-3v3-sd: supplied by vdd-3v3-sys
[ 0.628874] vdd-3v3-sd: 3300 mV
[ 0.630122] avdd-io-edp-1v05: supplied by avdd-1v05-pll
[ 0.630184] avdd-io-edp-1v05: 1050 mV
[ 0.630677] vdd-usb-hub-en: supplied by vdd-1v8
[ 0.630762] vdd-usb-hub-en: 5000 mV
[ 0.632141] camchar: rtcpu character device driver loaded
[ 0.632927] extcon-gpio-states extcon:extcon@1: Cable state:1, cable id:1
[ 0.634415] clocksource: Switched to clocksource arch_sys_counter
[ 0.675619] VFS: Disk quotas dquot_6.6.0
[ 0.675784] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.676321] nvmap_heap_init: nvmap_heap_init: created heap block cache
[ 0.676789] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000
[ 0.676840] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000)
[ 0.677068] cma: enabled page replacement for spfn=d7000, epfn=f0000
[ 0.677093] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful
[ 0.677120] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout
[ 0.677170] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048
[ 0.677195] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout
[ 0.677226] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways
[ 0.677248] nvmap_page_pool_init: Total RAM pages: 1010752
[ 0.677265] nvmap_page_pool_init: nvmap page pool size: 126344 pages (493 MB)
[ 0.677374] nvmap_background_zero_thread: PP zeroing thread starting.
[ 0.677896] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB)
[ 0.678980] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB)
[ 0.687177] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm
[ 0.687564] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm
[ 0.687837] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm
[ 0.688081] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm
[ 0.688281] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die
[ 0.688583] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz
[ 0.688603] pre_t19x_iso_plat_init(): max_iso_bw=33280000KB
[ 0.689047] NET: Registered protocol family 2
[ 0.690013] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.690250] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.690831] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.691014] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.691113] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.691537] NET: Registered protocol family 1
[ 0.692351] RPC: Registered named UNIX socket transport module.
[ 0.692382] RPC: Registered udp transport module.
[ 0.692399] RPC: Registered tcp transport module.
[ 0.692416] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.692441] PCI: CLS 0 bytes, default 64
[ 0.692698] Trying to unpack rootfs image as initramfs…
[ 0.701954] host1x 50000000.host1x: initialized
[ 0.703894] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 0.707273] audit: initializing netlink subsys (disabled)
[ 0.707401] audit: type=2000 audit(0.559:1): initialized
[ 0.708173] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 0.718300] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.719873] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.720700] 9p: Installing v9fs 9p2000 file system support
[ 0.724208] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240)
[ 0.724383] io scheduler noop registered
[ 0.724696] io scheduler cfq registered (default)
[ 0.727681] gic 702f9000.agic: GIC IRQ controller registered
[ 0.730683] iommu: Adding device 702ef000.adsp to group 33
[ 0.737413] iommu: Adding device aconnect@702c0000:adsp_audio to group 34
[ 0.737635] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered
[ 0.738271] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x81e6c0b
[ 0.738304] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4
[ 0.739988] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb
[ 0.740119] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb
[ 0.740238] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb
[ 0.740444] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1
[ 0.740554] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4
[ 0.740660] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4
[ 0.740780] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4
[ 0.740893] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4
[ 0.741000] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb
[ 0.741110] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb
[ 0.747512] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops
[ 0.748838] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000
[ 0.750756] tegra-pcie 1003000.pcie-controller: 4x1, 1x1 configuration
[ 0.752086] tegra-pcie 1003000.pcie-controller: PCIE: Enable power rails
[ 0.752452] tegra-pcie 1003000.pcie-controller: probing port 0, using 4 lanes
[ 0.753699] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe
[ 0.753950] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=750000, max_bw=1500000
[ 0.754224] Adding domain tsec-pd to PM domain host1x-pd
[ 0.756322] tegra-pcie 1003000.pcie-controller: probing port 1, using 1 lanes
[ 0.757561] tsec 54500000.tsec: initialized
[ 0.759255] tsec 54100000.tsecb: initialized
[ 0.760020] Adding domain nvdec-pd to PM domain host1x-pd
[ 0.763356] nvdec 54480000.nvdec: initialized
[ 0.764476] Adding domain vic03-pd to PM domain host1x-pd
[ 0.764678] Adding domain msenc-pd to PM domain host1x-pd
[ 0.764860] Adding domain nvjpg-pd to PM domain host1x-pd
[ 0.768768] falcon 54340000.vic: initialized
[ 0.770021] falcon 544c0000.nvenc: initialized
[ 0.771362] falcon 54380000.nvjpg: initialized
[ 0.775996] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1
[ 0.776131] display board info: id 0x0, fab 0x0
[ 0.776209] generic_infoframe_type: 0x87
[ 0.776354] tegradc tegradc.0: DT parsed successfully
[ 0.776418] tegradc tegradc.0: Display dc.ffffff800ab40000 registered with id=0
[ 0.776996] tegradc tegradc.0: Bootloader disp_param detected. Detected mode: 1920x1080 (on 0x0mm) pclk=148350781
[ 0.779836] tegradc tegradc.0: probed
[ 0.785025] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels
[ 0.789943] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 10 channels
[ 0.791074] tegra-pcie 1003000.pcie-controller: PCI host bridge to bus 0000:00
[ 0.791132] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.791158] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff]
[ 0.791183] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref]
[ 0.791213] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.791295] pci 0000:00:01.0: [10de:0fae] type 01 class 0x060400
[ 0.791489] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.791925] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized
[ 0.791974] pci 0000:00:02.0: [10de:0faf] type 01 class 0x060400
[ 0.792100] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.792345] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.792386] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.792492] kfuse 7000fc00.kfuse: initialized
[ 0.792625] pci 0000:01:00.0: [8086:24fd] type 00 class 0x028000
[ 0.792693] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit]
[ 0.793017] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.794390] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available
[ 0.795806] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0
[ 0.797452] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now
[ 0.797511] vdd-cpu: 708 <–> 1322 mV at 708 mV
[ 0.798052] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed
[ 0.799838] vdd-gpu: applied init 1000000uV constraint
[ 0.799881] vdd-gpu: 708 <–> 1323 mV at 997 mV
[ 0.800337] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed
[ 0.802625] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.802943] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000
[ 0.802992] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 0.803047] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit]
[ 0.803085] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit]
[ 0.803377] pci 0000:02:00.0: supports D1 D2
[ 0.803382] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.806209] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.806453] No Device Node present for smmu client: serial8250 !!
[ 0.806488] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000)
[ 0.806573] iommu: Adding device serial8250 to group 35
[ 0.810321] console [ttyS0] disabled
[ 0.810619] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra
[ 0.818624] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 0.818756] pci 0000:00:01.0: BAR 14: assigned [mem 0x13000000-0x130fffff]
[ 0.818763] pci 0000:00:02.0: BAR 14: assigned [mem 0x13100000-0x131fffff]
[ 0.818768] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 0.818780] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit]
[ 0.818815] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.818827] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff]
[ 0.818843] pci 0000:02:00.0: BAR 4: assigned [mem 0x13100000-0x13103fff 64bit]
[ 0.818869] pci 0000:02:00.0: BAR 2: assigned [mem 0x13104000-0x13104fff 64bit]
[ 0.818895] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff]
[ 0.818905] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 0.818909] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]
[ 0.818917] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff]
[ 0.820514] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt
[ 0.820522] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 0.820533] pcie_pme 0000:00:01.0:pcie001: service driver pcie_pme loaded
[ 0.820712] aer 0000:00:01.0:pcie002: service driver aer loaded
[ 0.821053] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt
[ 0.821058] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[ 0.821064] pcie_pme 0000:00:02.0:pcie001: service driver pcie_pme loaded
[ 0.821215] aer 0000:00:02.0:pcie002: service driver aer loaded
[ 3.245481] console [ttyS0] enabled
[ 3.246164] Console: switching to colour frame buffer device 240x67
[ 3.246972] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART
[ 3.247357] serial-tegra 70006200.serial: RX in PIO mode
[ 3.247498] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART
[ 3.248491] [drm] Initialized
[ 3.268886] brd: module loaded
[ 3.280684] loop: module loaded
[ 3.280814] tegra_profiler: version: 1.132, samples/io: 46/26
[ 3.280940] tegra_profiler: auth: init
[ 3.282378] THERMAL EST: found 2 subdevs
[ 3.282385] THERMAL EST num_resources: 0
[ 3.282391] [THERMAL EST subdev 0]
[ 3.282445] [THERMAL EST subdev 1]
[ 3.282924] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est
[ 3.282926] THERMAL EST: thz register success.
[ 3.283096] THERMAL EST: end of probe, return err: 0
[ 3.284448] hisi_sas: driver version v1.6
[ 3.288753] tegra-qspi 70410000.spi: Prod settings list not found
[ 3.295709] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes)
[ 3.295717] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0
[ 3.302323] libphy: Fixed MDIO Bus: probed
[ 3.303101] tun: Universal TUN/TAP device driver, 1.6
[ 3.303107] tun: (C) 1999-2004 Max Krasnyansky maxk@qualcomm.com
[ 3.304438] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 3.304441] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 3.304513] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[ 3.304515] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 3.304568] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[ 3.304571] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 3.304628] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4
[ 3.304631] Copyright(c) 1999 - 2017 Intel Corporation.
[ 3.309842] r8168 0000:02:00.0: enabling device (0000 → 0003)
[ 3.309882] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded
[ 3.324077] r8168 0000:02:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node
[ 3.324234] r8168 0000:02:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:e4:f2:c8 from device tree
[ 3.324861] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625.
[ 3.324899] r8168 Copyright (C) 2017 Realtek NIC software team nicfae@realtek.com
This program comes with ABSOLUTELY NO WARRANTY; for details, please see http://www.gnu.org/licenses/.
This is free software, and you are welcome to redistribute it under certain conditions; see http://www.gnu.org/licenses/.
[ 3.325513] PPP generic driver version 2.4.2
[ 3.325746] PPP BSD Compression module registered
[ 3.325753] PPP Deflate Compression module registered
[ 3.325793] PPP MPPE Compression module registered
[ 3.325800] NET: Registered protocol family 24
[ 3.325876] usbcore: registered new interface driver r8152
[ 3.325924] usbcore: registered new interface driver asix
[ 3.325988] usbcore: registered new interface driver ax88179_178a
[ 3.326035] usbcore: registered new interface driver cdc_ether
[ 3.326082] usbcore: registered new interface driver net1080
[ 3.326188] usbcore: registered new interface driver cdc_subset
[ 3.326229] usbcore: registered new interface driver zaurus
[ 3.326293] usbcore: registered new interface driver cdc_ncm
[ 3.326723] VFIO - User Level meta-driver version: 0.3
[ 3.328080] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 3.328105] ehci-pci: EHCI PCI platform driver
[ 3.328154] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 3.328194] ohci-pci: OHCI PCI platform driver
[ 3.328243] ohci-platform: OHCI generic platform driver
[ 3.331124] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP
[ 3.331725] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0
[ 3.332893] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f90a4400 id
[ 3.333012] tegra-xusb 70090000.xusb: Direct firmware load for tegra21x_xusb_firmware failed with error -2
[ 3.333015] tegra-xusb 70090000.xusb: Falling back to user helper
[ 3.334352] usbcore: registered new interface driver uas
[ 3.334442] usbcore: registered new interface driver usb-storage
[ 3.334569] usbcore: registered new interface driver usbserial
[ 3.337821] tegra-xudc-new 700d0000.xudc: device count: 1
[ 3.339247] tegra-xudc-new 700d0000.xudc: USB charger detection disabled
[ 3.339261] tegra-xudc-new 700d0000.xudc: vbus state: 1
[ 3.339279] tegra-xudc-new 700d0000.xudc: device mode on: 0
[ 3.339304] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 0
[ 3.339325] tegra-xudc-new 700d0000.xudc: active: 0 => 1
[ 3.339993] mousedev: PS/2 mouse device common for all mice
[ 3.340076] usbcore: registered new interface driver xpad
[ 3.585161] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0
[ 3.597902] rtc rtc1: alarm rtc device
[ 3.597918] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1
[ 3.597943] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock
[ 3.598611] i2c /dev entries driver
[ 3.600566] imx219 6-0010: tegracam sensor driver:imx219_v2.0.6
[ 3.624406] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10
[ 3.624484] imx219 6-0010: imx219_board_setup: error during i2c read probe (-121)
[ 3.624515] imx219 6-0010: board setup failed
[ 3.624614] imx219: probe of 6-0010 failed with error -121
[ 3.634090] max77620-power max77620-power: Event recorder REG_NVERC : 0x0
[ 3.675548] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2
[ 3.675552] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4
[ 3.676004] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 3.676018] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC
[ 3.676027] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC
[ 3.676199] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 3.676210] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC
[ 3.676216] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC
[ 3.676360] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 3.676370] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC
[ 3.676375] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature
[ 3.676555] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19
[ 3.677397] tegra_aotag tegra-aotag: Registering sensor 0
[ 3.677453] tegra_aotag tegra-aotag: Invalid temp readout
[ 3.677480] tegra_aotag tegra-aotag: Invalid temp readout
[ 3.677496] tegra_aotag tegra-aotag: Bound to TZ : ID 0
[ 3.677504] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0
[ 3.678452] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 3.678472] tegra_dfll_action dfll-cdev-cap: Tegra DFLL ‘cap cooling device’ registered
[ 3.678666] tegra_aotag tegra-aotag: Invalid temp readout
[ 3.678696] tegra_dfll_action dfll-cdev-floor: Tegra DFLL ‘floor cooling device’ registered
[ 3.679147] parse_throttle_dt_data: Num cap clks = 6
[ 3.679153] parse_throttle_dt_data: clk=cclk_g type=2
[ 3.679167] parse_throttle_dt_data: clk=gpu type=4
[ 3.679196] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0
[ 3.679216] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0
[ 3.679238] parse_throttle_dt_data: clk=cap.throttle.sclk type=0
[ 3.679241] parse_throttle_dt_data: clk=emc type=3
[ 3.680456] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 3.680563] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 3.680712] tegra_throttle_probe: probe successful. #cdevs=4
[ 3.681504] FAN dev name: pwm-fan
[ 3.681557] FAN:gpio request success.
[ 3.681631] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255
[ 3.681934] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal
[ 3.682123] pwm_fan_driver pwm-fan: fan tach request irq success
[ 3.682132] pwm_fan_driver pwm-fan: tach period: 1000
[ 3.682224] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2
[ 3.682229] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2
[ 3.682233] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2
[ 3.682237] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2
[ 3.682241] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3
[ 3.682245] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3
[ 3.682249] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3
[ 3.682253] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4
[ 3.682257] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4
[ 3.682261] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4
[ 3.682936] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds.
[ 3.683297] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 1)
[ 3.684196] device-mapper: uevent: version 1.0.3
[ 3.684682] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[ 3.690057] tegra210-cpufreq cpufreq: probe()…completed
[ 3.690801] sdhci: Secure Digital Host Controller Interface driver
[ 3.690802] sdhci: Copyright(c) Pierre Ossman
[ 3.690803] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.691296] sdhci-tegra sdhci-tegra.0: Got CD GPIO
[ 3.691644] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful
[ 3.691767] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300
[ 3.695213] tegra-se 70012000.se: tegra_se_probe: complete
[ 3.695734] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.696943] usbcore: registered new interface driver usbhid
[ 3.696944] usbhid: USB HID core driver
[ 3.715626] tegra21x_actmon 6000c800.actmon: in actmon_register()…
[ 3.715943] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all
[ 3.717738] nvpmodel: initialized successfully
[ 3.718840] usbcore: registered new interface driver snd-usb-audio
[ 3.718901] No Device Node present for smmu client: snd-soc-dummy !!
[ 3.718906] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000)
[ 3.718924] iommu: Adding device snd-soc-dummy to group 36
[ 3.738529] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr
[ 3.756873] OPE platform probe
[ 3.756969] OPE platform probe successful
[ 3.757354] OPE platform probe
[ 3.757438] OPE platform probe successful
[ 3.782697] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok
[ 3.782830] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok
[ 3.782952] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok
[ 3.783080] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok
[ 3.783201] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok
[ 3.783323] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok
[ 3.783446] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok
[ 3.783572] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok
[ 3.783697] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok
[ 3.783822] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok
[ 3.796554] u32 classifier
[ 3.796555] Actions configured
[ 3.796628] Initializing XFRM netlink socket
[ 3.797372] NET: Registered protocol family 10
[ 3.798127] NET: Registered protocol family 17
[ 3.798139] NET: Registered protocol family 15
[ 3.798215] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.798260] Bluetooth: RFCOMM socket layer initialized
[ 3.798269] Bluetooth: RFCOMM ver 1.11
[ 3.798273] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.798277] Bluetooth: HIDP socket layer initialized
[ 3.798294] 9pnet: Installing 9P2000 support
[ 3.798327] Key type dns_resolver registered
[ 3.800725] Registered cp15_barrier emulation handler
[ 3.800769] Registered setend emulation handler
[ 3.801863] registered taskstats version 1
[ 3.802534] Adding domain ve2-pd to PM domain host1x-pd
[ 3.802777] Adding domain ve-pd to PM domain host1x-pd
[ 3.907086] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0
[ 4.413371] tegradc tegradc.0: fb registered
[ 4.423977] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_mode.
[ 4.431229] tegradc tegradc.0: hdmi: tmds rate:148351K prod-setting:prod_c_hdmi_75m_150m
[ 4.439652] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by BL.
[ 4.446804] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by BL.
[ 4.454121] extcon-disp-state extcon:disp-state: cable 47 state 1
[ 4.460234] Extcon AUX1(HDMI) enable
[ 4.464242] tegradc tegradc.1: disp1 connected to head1->/host1x/sor
[ 4.470664] tegradc tegradc.1: No lt-data, using default setting
[ 4.470696] edid invalid
[ 4.479214] tegradc tegradc.1: No hpd-gpio in DT
[ 4.483850] tegradc tegradc.1: DT parsed successfully
[ 4.488922] tegradc tegradc.1: Display dc.ffffff800f4c0000 registered with id=1
[ 4.496998] tegradc tegradc.1: dpd enable lookup fail:-19
[ 4.497058] tegradc tegradc.0: nominal-pclk:148351648 parent:148350781 div:1.0 pclk:148350781 146868084~161703244
[ 4.516713] tegradc tegradc.1: probed
[ 4.534889] tegradc tegradc.1: fb registered
[ 4.542299] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1
[ 4.547582] isp 54600000.isp: initialized
[ 4.548372] isp 54680000.isp: initialized
[ 4.557571] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset)
[ 4.560092] clk_cbus_recalc_rate: no gbus parent
[ 4.560096] clk_cbus_round_rate: no gbus parent
[ 4.560098] clk_cbus_round_rate: no gbus parent
[ 4.560105] clk_cbus_recalc_rate: no gbus parent
[ 4.560206] clk_cbus_recalc_rate: no gbus parent
[ 4.560209] clk_cbus_round_rate: no gbus parent
[ 4.560210] clk_cbus_round_rate: no gbus parent
[ 4.560213] clk_cbus_recalc_rate: no gbus parent
[ 4.560904] tegra_dvfs: GPU-cap: registered
[ 4.560959] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled
[ 4.560960] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled
[ 4.560962] tegra dvfs: vdd-gpu: nominal 1038mV, offset 708000uV, step 10000uV, scaling enabled
[ 4.563195] tegra_dvfs: vdd-gpu-vts: registered
[ 4.564215] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS ‘floor cooling device’ registered
[ 4.564663] mmc0: hw tuning done …
[ 4.564693] mmc0: new ultra high speed SDR104 SDHC card at address 0001
[ 4.564841] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS ‘cap cooling device’ registered
[ 4.564993] mmcblk0: mmc0:0001 EB1QT 29.8 GiB
[ 4.565370] input: gpio-keys as /devices/gpio-keys/input/input1
[ 4.571382] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12
[ 4.597374] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:00:28 UTC (946688428)
[ 4.598339] vi 54080000.vi: vi_probe: ++
[ 4.602195] vi 54080000.vi: initialized
[ 4.604772] vi 54080000.vi: subdev nvcsi–1 bound
[ 4.604990] mmcblk mmc0:0001: Card claimed for testing.
[ 4.606198] Disable partitions left on by BL
[ 4.606200] disb
[ 4.606248] bwmgr: missing cdev-type property
[ 4.606348] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 4.606354] DRAM derating cdev registered.
[ 4.607351] vdd-1v8: disabling
[ 4.607353] vdd-fan: disabling
[ 4.607355] vdd-usb-vbus: disabling
[ 4.607356] vdd-usb-vbus2: disabling
[ 4.607366] avdd-io-edp-1v05: disabling
[ 4.607367] vdd-usb-hub-en: disabling
[ 4.607530] ALSA device list:
[ 4.607532] #0: tegra-hda at 0x70038000 irq 83
[ 4.607534] #1: tegra-snd-t210ref-mobile-rt565x
[ 4.764395] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0
[ 4.764416] tegradc tegradc.0: blank - powerdown
[ 4.799166] extcon-disp-state extcon:disp-state: cable 47 state 0
[ 4.799167] Extcon AUX1(HDMI) disable
[ 4.827311] tegradc tegradc.0: unblank
[ 4.864832] tegradc tegradc.0: nominal-pclk:148500000 parent:148500000 div:1.0 pclk:148500000 147015000~161865000
[ 4.864881] tegradc tegradc.0: hdmi: tmds rate:148500K prod-setting:prod_c_hdmi_75m_150m
[ 4.865867] tegradc tegradc.0: hdmi: get RGB quant from EDID.
[ 4.865871] tegradc tegradc.0: hdmi: get YCC quant from EDID.
[ 4.869095] extcon-disp-state extcon:disp-state: cable 47 state 1
[ 4.869096] Extcon AUX1(HDMI) enable
[ 4.869358] tegradc tegradc.0: sync windows ret = 250
[ 4.972989] tegradc tegradc.1: blank - powerdown
[ 4.979850] extcon-disp-state extcon:disp-state: cable 44 state 0 already set.
[ 4.979851] Extcon DP: HPD disabled
[ 4.979853] hpd: hpd_switch 0
[ 4.979860] hpd: switching from state 0 (Reset) to state 1 (Check Plug)
[ 4.979872] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0
[ 4.979876] hpd: switching from state 1 (Check Plug) to state 3 (Disabled)
[ 5.026225] extcon-disp-state extcon:disp-state: cable 40 state 1
[ 5.026226] Extcon HDMI: HPD enabled
[ 5.026236] tegradc tegradc.0: hdmi: plugged
[ 7.126460] EXT4-fs (mmcblk0p1): recovery complete
[ 7.141489] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[ 7.151687] VFS: Mounted root (ext4 filesystem) on device 179:1.
[ 7.163405] devtmpfs: mounted
[ 7.171534] Freeing unused kernel memory: 8512K
[ 7.365486] systemd[1]: System time before build time, advancing clock.
[ 7.402986] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.421523] cgroup: cgroup2: unknown option “nsdelegate”
[ 7.443164] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 7.469952] systemd[1]: Detected architecture arm64.
[ 7.509819] systemd[1]: Set hostname to .
[ 7.587847] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[ 7.607294] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[ 7.727291] random: systemd: uninitialized urandom read (16 bytes read)
[ 7.738128] systemd[1]: Created slice User and Session Slice.
[ 7.749272] random: systemd: uninitialized urandom read (16 bytes read)
[ 7.760298] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 7.774997] random: systemd: uninitialized urandom read (16 bytes read)
[ 7.784226] systemd[1]: Reached target Swap.
[ 7.793731] systemd[1]: Reached target User and Group Name Lookups.
[ 7.805420] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 7.929732] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[ 7.971135] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1268 [INFO] GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1)
[ 8.205549] systemd-journald[1962]: Received request to flush runtime journal from PID 1
[ 8.588962] using random self ethernet address
[ 8.595421] using random host ethernet address
[ 8.622589] Mass Storage Function, version: 2009/09/11
[ 8.622596] LUN: removable file: (no medium)
[ 8.634836] using random self ethernet address
[ 8.650658] using random host ethernet address
[ 8.674253] rndis0: HOST MAC f6:69:03:59:90:58
[ 8.674310] rndis0: MAC f6:69:03:59:90:59
[ 8.674844] usb0: HOST MAC f6:69:03:59:90:5a
[ 8.674867] usb0: MAC f6:69:03:59:90:5b
[ 8.674896] tegra-xudc-new 700d0000.xudc: ep 0 (type: 0, dir: out) enabled
[ 8.896534] l4tbr0: port 1(rndis0) entered blocking state
[ 8.896569] l4tbr0: port 1(rndis0) entered disabled state
[ 8.897064] device rndis0 entered promiscuous mode
[ 8.911611] IPv6: ADDRCONF(NETDEV_UP): rndis0: link is not ready
[ 8.916195] l4tbr0: port 2(usb0) entered blocking state
[ 8.916200] l4tbr0: port 2(usb0) entered disabled state
[ 8.916338] device usb0 entered promiscuous mode
[ 8.923698] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
[ 8.923705] l4tbr0: port 2(usb0) entered blocking state
[ 8.923708] l4tbr0: port 2(usb0) entered forwarding state
[ 9.151052] random: crng init done
[ 9.156011] random: 7 urandom warning(s) missed due to ratelimiting
[ 9.628385] tegra-xusb 70090000.xusb: cannot find firmware…retry after 1 second
[ 9.682482] l4tbr0: port 2(usb0) entered disabled state
[ 9.798089] nvs_dsm nvs_dsm: dsm_probe
[ 9.798115] nvs_dsm nvs_dsm: dsm_remove
[ 9.798118] nvs_dsm nvs_dsm: dsm_probe done
[ 10.274496] Intel(R) Wireless WiFi driver for Linux
[ 10.274500] Copyright(c) 2003- 2015 Intel Corporation
[ 10.274729] iwlwifi 0000:01:00.0: enabling device (0000 → 0002)
[ 10.286387] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-26.ucode failed with error -2
[ 10.298438] iwlwifi 0000:01:00.0: Falling back to user helper
[ 10.649452] tegra-xusb 70090000.xusb: Firmware timestamp: 2017-11-03 13:36:19 UTC, Version: 50.20 release
[ 10.649494] tegra-xusb 70090000.xusb: xHCI Host Controller
[ 10.649517] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1
[ 10.650389] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010
[ 10.650483] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000
[ 10.650647] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 10.650653] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.650656] usb usb1: Product: xHCI Host Controller
[ 10.650659] usb usb1: Manufacturer: Linux 4.9.140-tegra xhci-hcd
[ 10.650662] usb usb1: SerialNumber: 70090000.xusb
[ 10.651116] hub 1-0:1.0: USB hub found
[ 10.651151] hub 1-0:1.0: 5 ports detected
[ 10.651595] tegra-xusb 70090000.xusb: xHCI Host Controller
[ 10.651605] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2
[ 10.651679] usb usb2: We don’t know the algorithms for LPM for this host, disabling LPM.
[ 10.651751] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 10.651755] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.651758] usb usb2: Product: xHCI Host Controller
[ 10.651760] usb usb2: Manufacturer: Linux 4.9.140-tegra xhci-hcd
[ 10.651763] usb usb2: SerialNumber: 70090000.xusb
[ 10.652173] hub 2-0:1.0: USB hub found
[ 10.652239] hub 2-0:1.0: 4 ports detected
[ 10.682084] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.686604] eth0: 0xffffff800a2fe000, 00:04:4b:e4:f2:c8, IRQ 404
[ 10.754602] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1
[ 10.754661] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 2
[ 10.754868] usb usb2: usb_suspend_both: status 0
[ 10.756439] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.978517] usb 1-2: new high-speed USB device number 2 using tegra-xusb
[ 11.017595] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411
[ 11.017602] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 11.017605] usb 1-2: Product: 4-Port USB 2.1 Hub
[ 11.017608] usb 1-2: Manufacturer: Generic
[ 11.018946] hub 1-2:1.0: USB hub found
[ 11.020043] hub 1-2:1.0: 4 ports detected
[ 11.123484] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb
[ 11.146469] tegra-xusb-padctl 7009f000.xusb_padctl: power down UTMI pad 1
[ 11.158644] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411
[ 11.158650] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 11.158654] usb 2-1: Product: 4-Port USB 3.1 Hub
[ 11.158656] usb 2-1: Manufacturer: Generic
[ 11.162942] hub 2-1:1.0: USB hub found
[ 11.165509] hub 2-1:1.0: 4 ports detected
[ 11.166500] usb 1-2: usb_suspend_both: status 0
[ 11.266714] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-25.ucode failed with error -2
[ 11.277595] iwlwifi 0000:01:00.0: Falling back to user helper
[ 11.278441] usb 1-3: new full-speed USB device number 3 using tegra-xusb
[ 11.296766] usb 1-3: New USB device found, idVendor=8087, idProduct=0a2b
[ 11.296774] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 11.334464] usb 2-1: usb_suspend_both: status 0
[ 11.462502] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-24.ucode failed with error -2
[ 11.462535] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1
[ 11.475212] iwlwifi 0000:01:00.0: Falling back to user helper
[ 11.488198] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-23.ucode failed with error -2
[ 11.499181] iwlwifi 0000:01:00.0: Falling back to user helper
[ 11.553804] iwlwifi 0000:01:00.0: loaded firmware version 22.391740.0 op_mode iwlmvm
[ 11.583568] usb 2-1-port1: over-current condition
[ 11.613613] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless AC 8265, REV=0x230
[ 11.616458] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 11.617645] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 11.706582] usb 1-2-port1: over-current condition
[ 11.741169] ieee80211 phy0: Selected rate control algorithm ‘iwl-mvm-rs’
[ 11.742063] thermal thermal_zone6: failed to read out thermal zone (-5)
[ 11.748810] thermal thermal_zone6: Registering thermal zone thermal_zone6 for type iwlwifi
[ 11.797025] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 11.799826] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 11.800335] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 11.807619] usb 2-1-port2: over-current condition
[ 11.920718] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 11.920978] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled
[ 11.926540] usb 1-2-port2: over-current condition
[ 11.984866] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 12.031683] usb 2-1-port1: over-current condition
[ 12.150733] usb 1-2-port1: over-current condition
[ 12.203727] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 12.251614] usb 2-1-port2: over-current condition
[ 12.314607] tegradc tegradc.0: blank - powerdown
[ 12.367005] extcon-disp-state extcon:disp-state: cable 47 state 0
[ 12.367007] Extcon AUX1(HDMI) disable
[ 12.386551] tegradc tegradc.0: unblank
[ 12.398506] tegradc tegradc.0: nominal-pclk:148500000 parent:148500000 div:1.0 pclk:148500000 147015000~161865000
[ 12.398574] tegradc tegradc.0: hdmi: tmds rate:148500K prod-setting:prod_c_hdmi_75m_150m
[ 12.399593] tegradc tegradc.0: hdmi: get RGB quant from EDID.
[ 12.399600] tegradc tegradc.0: hdmi: get YCC quant from EDID.
[ 12.402848] extcon-disp-state extcon:disp-state: cable 47 state 1
[ 12.402849] Extcon AUX1(HDMI) enable
[ 12.408769] tegradc tegradc.0: unblank
[ 12.408778] tegradc tegradc.1: blank - powerdown
[ 12.471600] usb 2-1-port1: over-current condition
[ 12.590598] usb 1-2-port1: over-current condition
[ 12.691583] usb 2-1-port2: over-current condition
[ 12.814581] usb 1-2-port2: over-current condition
[ 12.915588] usb 2-1-port1: over-current condition
[ 13.152022] fuse init (API version 7.26)
[ 13.910744] usb 1-2-port1: over-current condition
[ 14.367423] tegradc tegradc.0: blank - powerdown
[ 14.439904] extcon-disp-state extcon:disp-state: cable 47 state 0
[ 14.439912] Extcon AUX1(HDMI) disable
[ 14.453936] tegradc tegradc.0: unblank
[ 14.460092] tegradc tegradc.0: nominal-pclk:148500000 parent:148500000 div:1.0 pclk:148500000 147015000~161865000
[ 14.460167] tegradc tegradc.0: hdmi: tmds rate:148500K prod-setting:prod_c_hdmi_75m_150m
[ 14.461170] tegradc tegradc.0: hdmi: get RGB quant from EDID.
[ 14.461177] tegradc tegradc.0: hdmi: get YCC quant from EDID.
[ 14.464430] extcon-disp-state extcon:disp-state: cable 47 state 1
[ 14.464432] Extcon AUX1(HDMI) enable
[ 14.464977] tegradc tegradc.0: unblank
[ 14.464985] tegradc tegradc.1: blank - powerdown
[ 15.485085] wlan0: authenticate with c0:25:e9:3a:0a:de
[ 15.495013] wlan0: send auth to c0:25:e9:3a:0a:de (try 1/3)
[ 15.500068] wlan0: authenticated
[ 15.502470] wlan0: associate with c0:25:e9:3a:0a:de (try 1/3)
[ 15.503401] wlan0: RX AssocResp from c0:25:e9:3a:0a:de (capab=0x1011 status=0 aid=12)
[ 15.505155] wlan0: associated
[ 15.526948] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 16.730544] usb 1-2-port2: over-current condition
[ 23.467024] usb 1-2-port1: over-current condition
[ 23.686962] usb 1-2-port2: over-current condition
[ 31.495021] usb 1-2-port2: over-current condition
[ 35.611070] usb 1-2.3: new full-speed USB device number 4 using tegra-xusb
[ 35.635988] usb 1-2.3: New USB device found, idVendor=05ac, idProduct=0220
[ 35.636061] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 35.636104] usb 1-2.3: Product: 66EC-S
[ 35.636142] usb 1-2.3: Manufacturer: CATEX TECH.
[ 35.636178] usb 1-2.3: SerialNumber: CA2017120001
[ 35.645240] input: CATEX TECH. 66EC-S as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.0/0003:05AC:0220.0001/input/input2
[ 35.708507] apple 0003:05AC:0220.0001: input,hidraw0: USB HID v1.10 Keyboard [CATEX TECH. 66EC-S] on usb-70090000.xusb-2.3/input0
[ 35.709917] apple 0003:05AC:0220.0002: hidraw1: USB HID v1.00 Device [CATEX TECH. 66EC-S] on usb-70090000.xusb-2.3/input1
[ 35.714509] input: CATEX TECH. 66EC-S as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.2/0003:05AC:0220.0003/input/input3
[ 35.777654] apple 0003:05AC:0220.0003: input,hidraw2: USB HID v1.10 Keyboard [CATEX TECH. 66EC-S] on usb-70090000.xusb-2.3/input2
[ 37.307585] usb 1-2-port1: over-current condition
[ 44.679154] usb 1-2-port1: over-current condition
[ 47.061642] usb 1-2.3: USB disconnect, device number 4
[ 48.915397] usb 1-2-port1: over-current condition
[ 50.564424] usb 2-1-port1: over-current condition
[ 57.380800] extcon-disp-state extcon:disp-state: cable 47 state 0
[ 57.380840] Extcon AUX1(HDMI) disable
[ 57.398516] tegradc tegradc.0: blank - powerdown
[ 57.398592] extcon-disp-state extcon:disp-state: cable 40 state 0
[ 57.398595] Extcon HDMI: HPD disabled
[ 57.398617] tegradc tegradc.0: hdmi: unplugged
[ 57.439143] tegradc tegradc.0: blank - powerdown
[ 57.439155] tegradc tegradc.0: unblank
[ 57.439182] tegradc tegradc.0: unblank
[ 57.439190] tegradc tegradc.1: blank - powerdown
[ 91.510991] usb 1-2-port2: over-current condition
[ 107.408544] usb 2-1-port2: over-current condition
[ 133.859458] usb 1-2-port2: over-current condition
[ 174.699400] usb 1-2-port1: over-current condition
[ 193.386874] usbcore: registered new interface driver btusb
[ 193.387933] Bluetooth: hci0: Bootloader revision 0.0 build 26 week 38 2015
[ 193.388937] Bluetooth: hci0: Device revision is 16
[ 193.388941] Bluetooth: hci0: Secure boot is enabled
[ 193.388943] Bluetooth: hci0: OTP lock is disabled
[ 193.388945] Bluetooth: hci0: API lock is enabled
[ 193.388946] Bluetooth: hci0: Debug lock is disabled
[ 193.388949] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[ 193.401211] Bluetooth: hci0: Found device firmware: intel/ibt-12-16.sfi
[ 193.458060] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 193.458071] Bluetooth: BNEP socket layer initialized
[ 195.143386] Bluetooth: hci0: Waiting for firmware download to complete
[ 195.143972] Bluetooth: hci0: Firmware loaded in 1716113 usecs
[ 195.144142] Bluetooth: hci0: Waiting for device to boot
[ 195.156519] Bluetooth: hci0: Device booted in 12113 usecs
[ 195.161692] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc
[ 195.165303] Bluetooth: hci0: Applying Intel DDC parameters completed
[ 223.971675] usb 1-2-port1: over-current condition
[ 230.671429] usb 1-2-port2: over-current condition
[ 242.636724] Host read timeout at address 5458045c
[ 242.642555] tegradc tegradc.0: blank - powerdown
[ 242.642629] tegradc tegradc.0: unblank
[ 242.669749] tegradc tegradc.0: nominal-pclk:148500000 parent:148500000 div:1.0 pclk:148500000 147015000~161865000
[ 242.669846] tegradc tegradc.0: hdmi: tmds rate:148500K prod-setting:prod_c_hdmi_75m_150m
[ 242.670868] tegradc tegradc.0: hdmi: get RGB quant from EDID.
[ 242.670875] tegradc tegradc.0: hdmi: get YCC quant from EDID.
[ 242.674355] extcon-disp-state extcon:disp-state: cable 47 state 1
[ 242.674356] Extcon AUX1(HDMI) enable
[ 242.675907] extcon-disp-state extcon:disp-state: cable 40 state 1
[ 242.675911] Extcon HDMI: HPD enabled
[ 242.675945] tegradc tegradc.0: hdmi: plugged
[ 242.730907] tegradc tegradc.0: blank - powerdown
[ 242.789749] extcon-disp-state extcon:disp-state: cable 47 state 0
[ 242.789754] Extcon AUX1(HDMI) disable
[ 242.808567] tegradc tegradc.0: unblank
[ 242.820408] tegradc tegradc.0: nominal-pclk:148500000 parent:148500000 div:1.0 pclk:148500000 147015000~161865000
[ 242.820486] tegradc tegradc.0: hdmi: tmds rate:148500K prod-setting:prod_c_hdmi_75m_150m
[ 242.821496] tegradc tegradc.0: hdmi: get RGB quant from EDID.
[ 242.821503] tegradc tegradc.0: hdmi: get YCC quant from EDID.
[ 242.826562] extcon-disp-state extcon:disp-state: cable 47 state 1
[ 242.826563] Extcon AUX1(HDMI) enable
[ 242.826715] tegradc tegradc.0: unblank
[ 242.826722] tegradc tegradc.1: blank - powerdown
[ 244.504976] input: M585/M590 as /devices/virtual/misc/uhid/0005:046D:B01B.0004/input/input4
[ 244.505402] hid-generic 0005:046D:B01B.0004: input,hidraw0: BLUETOOTH HID v0.11 Keyboard [M585/M590] on 34:13:E8:62:80:AD
[ 250.099451] usb 1-2-port2: over-current condition
[ 265.193862] extcon-disp-state extcon:disp-state: cable 47 state 0
[ 265.193901] Extcon AUX1(HDM
Does it mean the usb ports are physically damaged? any other possibilities?
Thank you in advance.
wenhailiu94
I don’t think we have the same issue but the symptoms appear to be the same, according to my dmesg log, I don’t have your “over-current” message but I do have this:
22:08:05.284 -> [ 5.075558] vdd-usb-vbus: disabling
22:08:05.284 -> [ 5.079065] vdd-usb-vbus2: disabling
22:08:05.284 -> [ 5.082650] avdd-io-edp-1v05: disabling
22:08:05.284 -> [ 5.086495] vdd-usb-hub-en: disabling
Sadly, I have not been able to get it to work… WayneWWW, care to chime in?
jsyang.ca,
Are you sure this is a full log? I saw the log has been cut off by the forum system.
Codeblock or attachment can prevent it.
In below log, usb device is up, but I don’t see any error message afterwards.
[ 35.611070] usb 1-2.3: new full-speed USB device number 4 using tegra-xusb
[ 35.635988] usb 1-2.3: New USB device found, idVendor=05ac, idProduct=0220
[ 35.636061] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 35.636104] usb 1-2.3: Product: 66EC-S
[ 35.636142] usb 1-2.3: Manufacturer: CATEX TECH.
[ 35.636178] usb 1-2.3: SerialNumber: CA2017120001
[ 35.645240] input: CATEX TECH. 66EC-S as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.0/0003:05AC:0220.0001/input/input2
[ 35.708507] apple 0003:05AC:0220.0001: input,hidraw0: USB HID v1.10 Keyboard [CATEX TECH. 66EC-S] on usb-70090000.xusb-2.3/input0
[ 35.709917] apple 0003:05AC:0220.0002: hidraw1: USB HID v1.00 Device [CATEX TECH. 66EC-S] on usb-70090000.xusb-2.3/input1
[ 35.714509] input: CATEX TECH. 66EC-S as /devices/70090000.xusb/usb1/1-2/1-2.3/1-2.3:1.2/0003:05AC:0220.0003/input/input3
[ 35.777654] apple 0003:05AC:0220.0003: input,hidraw2: USB HID v1.10 Keyboard [CATEX TECH. 66EC-S] on usb-70090000.xusb-2.3/input2
Hi WayneWWW, I did not see an attachment field for replying in this thread but I already posted a link to the full dmesg log I was able to get: I put it up as a public GitHub Gist here:
edit: it wasn’t obvious but I just figured out how to do it, the log is also attached to this post.
dmesg-jetson-nano-no-usb.txt (80.6 KB)
jsyang.ca,
Your latest kernel log is different with #8. Which one is correct log? Also, the xusb firmware is gone in latest kernel log and never loaded up.
22:08:04.570 -> [ 3.766817] tegra-xusb 70090000.xusb: Direct firmware load for tegra21x_xusb_firmware failed with error -2
22:08:04.570 -> [ 3.766821] tegra-xusb 70090000.xusb: Falling back to user helper
Are you using pure driver from jetpack/sdkmanager? Do you have any peripheral connected?
I am using the image from the official jetson nano developer kit Getting Started guide, no changes at all. Flashed straight to SD card and that is what I’m getting.
https://developer.nvidia.com/embedded/dlc/jetson-nano-dev-kit-sd-card-image
It worked previous to installing the Intel 8265NGW card, I have removed the card since and the USB ports are still non-functional. I was using a USB Wifi dongle before installing the card and that was working fine.
jsyang.ca,
So the log in #8 is actually a working case? Do you mean after you try Intel 8265NGW, the usb is dead after then and the log is in #12?
I just need to clarify which log has the problem and what did you do. Do you install anything for setting up 8265?
#8 was not posted by me but by user wenhailiu94 who has been commenting on this thread. I did not look at his logs.
I installed nothing for the 8265, all USB ports stopped working immediately after I installed it and tried to boot the system.
Oops, sorry that I mess it up. Didn’t notice there are two users here.
I will investigate this issue.
In brief, You once set up Intel 8265NGW. After that, even removing the 8265 device cannot recover the usb, right?
Yes, that’s right. Sadly, the USB ports don’t even appear to be providing power.
Hi,
Could you help check below file on your tegra? Does it exist?
nvidia@nvidia-desktop:/lib/firmware$ ls tegra21x_xusb_firmware -al
-rw-r--r-- 1 root root 126464 五 29 11:13 tegra21x_xusb_firmware